Tornado 98167 Chassis Assembly (Part 2)

Chassis parts, part 2, for the Tornado 98167 Marathon 800 (8 Gallon, 230V). This sheet is the structural half of the machine — the chassis weldment itself, the wheels and axle, and the nozzle that meets the carpet.

What is on Tornado 98167 chassis sheet 2

The chassis (19241) is the weldment everything else bolts to. It rides on 10-inch wheels (02661) on an axle (19143) held by retaining clamps and E-rings (03470), with spacers and washers setting the end float. The 20-inch nozzle (19168, ordered with the hose adapter tube 19197) is carried on the shroud/nozzle mounting bracket weldment (19155) and hinges on a 1/4″ x 2″ hinge (19148). A 2-inch steel supported hose (18687) runs the recovery path. The quick-disconnect coupler (PX5) takes the solution line. The fastener set runs from 1/2-13 x 1″ screws (05441) and 3/8-16 x 1-1/4″ screws (19171) down to lock washers (01574), lock nuts (15092) and the M4 x 16 screws (23192).

Shared with the 115-volt machine

Nothing on this sheet is voltage-specific. Every part number here is shared with the 115-volt 98166 Marathon 800, and much of it with the Marathon 1200 as well, so a part ordered from this page fits either voltage of the machine.

When a Tornado 98167 chassis part needs replacing

Wheels and axle hardware are the usual wear items — a wheel that wobbles is normally a missing E-ring or a worn bushing rather than a bad wheel. A nozzle that leaves a wet stripe is either sitting at the wrong height on its bracket or has a worn lip. If the machine has been dropped or dragged up stairs, check the hinge and the mounting bracket weldment for distortion before replacing the nozzle itself.

Not sure which part you need? Call 763-535-0770 with the model and serial number from the plate on the machine. Twin City Vacuum, 5415 West Broadway, Crystal, MN 55428, has been selling and servicing Tornado equipment since 1956. Browse all Tornado cleaning equipment parts, or see the machine at tornadovac.com.

Frequently Asked Questions about Tornado 98167 frame and nozzle parts

What frame and nozzle parts fit my Tornado 98167?

The structural half of the machine: the chassis weldment 19241, the 20 in. aluminium nozzle 19168, the shroud and nozzle mounting bracket weldment 19155, the axle 19143, the hinge 19148, the shroud pivot spacer 19259 and the stainless fasteners that tie them together.

Do any of these Tornado 98167 parts depend on voltage?

None of them. Every item on this sheet is mechanical and is shared with the 115-volt Tornado 98166 — the same chassis, nozzle, axle and brackets are used on both machines. If you are ordering structural parts, the 115-volt and 230-volt lists agree.

The nozzle on my Tornado 98167 is not picking up evenly. What should I check?

Look at the 20 in. aluminium nozzle 19168 for a nick or flat spot along its lip, and check the shroud and nozzle mounting bracket 19155 and the hinge 19148 for play — a nozzle that can rock cannot hold an even gap to the carpet. Uneven wetting rather than uneven pickup points instead at the spraybar on the brush sheet.

How do I order a Tornado 98167 chassis part or get help identifying one?

You can order any Tornado 98167 part on this page directly from its own product page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can confirm the right part against your machine’s serial number before you buy.

Showing 1–20 of 22 results