Foot, Right, Dryer Kickstand X8928
$3.99
Genuine OEM right-hand kickstand foot (part# X8928) — the moulded end cap the kickstand wire pivots in on Tornado and Powr-Flite carpet dryers. Sold singly; the left-hand foot is a separate part.
Genuine OEM foot, right, dryer kickstand (part# X8928) for Tornado and Powr-Flite carpet dryers and air movers. This is the moulded end piece on the right-hand side of the machine that the wire kickstand pivots in. It sets the angle the dryer tips to, takes the load when the machine is propped back, and acts as the rear contact point on the floor.
This is the right-hand part only. The left-hand foot is a separate, mirror-image item with its own part number, and the two are not interchangeable. If both sides are damaged — which is common, because they usually fail together — you need one of each.
How it fails: the kickstand foot is the part that hits the ground when the dryer is tipped back, dropped off a tailgate or kicked into position. The pivot pocket wears oval, the moulding cracks at the thin section around the pivot, or the whole foot splits off and the kickstand wire falls free. On an older machine the plastic also gets brittle, so a knock that it would have shrugged off when new takes a chunk out of it.
When to replace it: if the kickstand will not hold the machine at its set angle; if the wire has sloppy side-to-side play where it enters the foot; if you can see cracks radiating from the pivot pocket; or if the foot has broken away. A kickstand that collapses while the machine is propped lets the dryer drop onto its intake — and that is a far more expensive repair than a four-dollar foot.
Fitting: support the machine so it cannot fall, release the kickstand wire on the side you are working on, swap the foot and refit the hardware. Check the opposite side while you are there; if one has worn oval, the other is usually close behind.
Compatible Models
- Tornado Windshear SD3500 Model 98776 (and the 98777 230V export version)
- Tornado 98780
- Powr-Flite PD350, PD500 and PDH2 carpet dryers
- and other Tornado and Powr-Flite air-mover and dryer models — call 763-535-0770 to confirm
Frequently Asked Questions
What does the right kickstand foot (part# X8928) do?
It is the moulded end piece the wire kickstand pivots in on the right-hand side of the dryer. It sets the tipped-back angle of the machine, carries the load when the dryer is propped, and acts as the rear floor contact.
Does part# X8928 include the left-hand foot as well?
No. X8928 is the right-hand foot only. The left-hand foot is a separate mirror-image part with its own number, and the two cannot be swapped. If both sides are damaged you need one of each.
How do I know if my X8928 kickstand foot needs replacing?
Replace it if the kickstand no longer holds the machine at its set angle, if the wire has noticeable side-to-side play where it enters the foot, if cracks radiate from the pivot pocket, or if the foot has broken away. A kickstand that collapses drops the dryer onto its intake.
What models is the right kickstand foot (part# X8928) compatible with?
It fits the Tornado Windshear SD3500 Model 98776 (and the 98777 230V export version), Tornado 98780, and the Powr-Flite PD350, PD500 and PDH2 carpet dryers, plus other models in those families. Call 763-535-0770 to confirm.
How do I order the right kickstand foot (part# X8928) or get help?
You can add the right kickstand foot (part# X8928) directly to your cart on this page, or call us at 763-535-0770.
You can add this part directly to your cart on this page, or call us at 763-535-0770.






Reviews
There are no reviews yet