Heat Shrink, Black, 1/2 in. Wide, Flexible Poly 72470A

$2.99

Genuine OEM heat shrink tubing (part# 72470A), 1/2 in. wide black flexible polyolefin, for insulating and sealing wiring splices and terminal crimps inside portable air mover housings – fits Tornado Windshear and Powr-Flite air mover models (see full compatibility list below).

Genuine OEM heat shrink tubing (part# 72470A) – 1/2 in. wide black flexible polyolefin – used to insulate and seal wiring splices and terminal connections inside portable air mover housings. It is a shared OEM service part that appears on both Tornado Windshear and Powr-Flite air mover wiring, so the same tubing covers repairs on either brand (see the full compatibility list below).

What the 72470A heat shrink tubing does

Every electrical joint inside an air mover is a potential failure point. The cord enters the housing, feeds the GFCI or breaker, runs to the speed switch and on to the motor, and each of those transitions is a crimp or a splice sitting a few inches from a spinning fan and, very often, a wet floor. Heat shrink tubing is what turns a bare crimp into a sealed one. The sleeve is cut to length, slid over the joint before the connector is crimped, then warmed with a heat gun until it draws down tight against the wire jacket on both sides. The result is a joint that resists moisture wicking, abrasion against the housing, and the constant low-level vibration that works ordinary electrical tape loose within a season.

Polyolefin is the standard material for this job because it stays flexible after it shrinks rather than going hard and cracking. The 1/2 in. size covers the larger joints in an air mover – motor leads, cord splices and multi-wire bundles – where a smaller sleeve will not pass over the connector body.

When to replace it

Heat shrink is a consumable, not a serviceable component. You buy it to make a repair, and you replace the old sleeve whenever you open a joint. Cut off and renew any tubing that has split, gone chalky or brittle with age, crept away from the joint it was covering, or discolored from heat. Browning or a burnt smell around a sleeve means the joint underneath has been running hot and should be inspected before it is re-insulated. Never slide an already-shrunk sleeve back over a new splice – it has no shrink left and will not seal.

Specifications

  • Part number: 72470A
  • Material: flexible polyolefin
  • Color: black
  • Size: 1/2 in. wide
  • Type: heat shrink tubing (insulating sleeve)
  • UPC: 098612585848

Compatible Models

The factory fitment record places part# 72470A on the Tornado Windshear 98782 sidedraft air mover and on the Powr-Flite PDF6WRD air mover. It is also listed on the Windshear 98783 and 98785, which are the 230V export builds and are not sold in the United States. If you are repairing a splice on any of these machines, this is the tubing the factory specifies.

  • Tornado Windshear 98782 (sidedraft air mover)
  • Powr-Flite PDF6WRD air mover
  • Tornado Windshear 98783 and 98785 – 230V export builds, not sold in the US

Frequently Asked Questions

What does the heat shrink tubing (part# 72470A) do on a Tornado Windshear air mover?

Heat shrink tubing (part# 72470A) is the insulating sleeve that covers wiring splices, butt connectors and terminal crimps inside the air mover housing. A length is slid over the joint and warmed until it contracts tightly around the conductor, sealing the copper away from moisture, dust and vibration. On a machine that is dragged across wet carpet and bounced in and out of a van every day, that sealed joint is what keeps a repaired wire from shorting against the housing or the motor frame.

How do I know if the heat shrink tubing (part# 72470A) on my air mover needs replacing?

Look at the wiring whenever the housing is open. Tubing that has split along its length, gone chalky or brittle, slid away from the joint, or shows browning and a burnt smell has lost its insulating value and should be cut off and replaced. You also need fresh tubing any time you make a new splice – at a cut cord, a replaced switch, a new motor lead or a repaired GFCI pigtail – because the old sleeve cannot be reused once it has shrunk.

What models is the heat shrink tubing (part# 72470A) compatible with?

Part# 72470A is a shared OEM service part. The factory record lists it on the Tornado Windshear 98782 sidedraft air mover and on the Powr-Flite PDF6WRD. It is also listed on the 230V export versions of the Windshear (98783 and 98785), which are not sold in the United States. Because it is plain 1/2 in. flexible polyolefin tubing, it serves any splice on those machines that falls within its range rather than one specific location.

How do I order the heat shrink tubing (part# 72470A) or get help?

You can add the heat shrink tubing (part# 72470A) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.

Not sure this is the sleeve your repair needs? Browse the full Tornado Windshear air mover parts range, or call us at 763-535-0770 and we will confirm it against your machine.

Reviews

There are no reviews yet

Be the first to review “Heat Shrink, Black, 1/2 in. Wide, Flexible Poly 72470A”

Your email address will not be published. Required fields are marked *