Find genuine Titan T8000 power nozzle parts for the Titan T8000 bagless canister vacuum. Can’t find your part? Call us at 763-535-0770.
Click a red dot on the Titan T8000 power nozzle diagram to open that part. Parts we do not carry online show a call-us note, and their dots jump to that row in the numbered parts list below.
1. Power Nozzle Bumper Strip – 47-7301-062. Window Height Adjust – 5910041583. Power Nozzle Rear Cover Plate – 47-7706-074. Power Nozzle Headlight Window – 47-7701-025. Power Nozzle Lamp Board Assembly – 47-7601-036. Power Nozzle PCB Assembly – 47-8004-047. Power Nozzle Cover – 5910191098. Wire Nut – 5910041569. Power Nozzle Brush Roll Assembly – 47-3404-0110. Power Nozzle Indicator Block Assembly – 47-7105-0411. Power Nozzle Rear Wheel Assembly – 47-7906-0512. Power Nozzle Rear Wheel Shaft – 47-7102-0713. Lifter – 59100417814. Power Nozzle Base – 47-7204-0415. Power Nozzle Front Axle Assembly – 47-7100-0916. Power Nozzle Handle Release – 47-6201-0917. Power Nozzle Belt – 47-3308-0818. Power Nozzle Motor Assembly – 47-8506-0719. Power Nozzle Motor Gasket – 47-8902-0720. Metal Bracket – 59100417721. Swivel Seal – 59100418222. Power Nozzle Locking Clip – 59100419123. Power Nozzle Swivel Neck – 47-6205-0524. Power Nozzle Plug Wire – 47-5700-0725. Power Nozzle Sensor Cover A – 47-6210-0826. Power Nozzle Support B – 47-6206-0427. Power Nozzle Spring – 59100418828. Power Nozzle Foot Pedal Quick Release – 47-6209-0129. Power Nozzle Sensor Cover B – 47-6211-0730. Screw – 59100415231. Screw – 59100417232. Screw – 59100419033. Power Nozzle – 47-4806-0330. Screw – 59100415211. Power Nozzle Rear Wheel Assembly – 47-7906-0512. Power Nozzle Rear Wheel Shaft – 47-7102-0721. Swivel Seal – 59100418230. Screw – 591004152Find genuine Titan T8000 power nozzle replacement parts for the Titan T8000 bagless canister vacuum. The power nozzle diagram shows the brush roll, belt and motor, the headlight lamp board and window, the circuit board, the base and covers, the wheels, front axle and pedal, the swivel neck and plug wire, and the complete power nozzle. Twin City Vacuum has been selling and servicing vacuums since 1956. Call 763-535-0770 or stop by 5415 West Broadway, Crystal, MN 55428.
Titan T8000 Power Nozzle Parts List
Titan T8000 Power Nozzle Parts: What to Look For
The power nozzle belt and the brush roll are the parts that wear out first. A stretched or broken belt stops the brush roll from turning, and worn bristles leave dirt in the carpet even when the belt is good. Replace the belt whenever you replace the brush roll.
If the brush roll will not turn with a good belt, check the power nozzle motor and the circuit board. A dark headlight usually means a failed lamp board. When the nozzle housing is badly cracked or several parts are worn at once, the complete power nozzle can cost less than the repairs.
Most T8000 power nozzle parts are shared with the T9400. A few small parts, including the window height adjuster, the lifter, the metal bracket, the wire nut and some screws, are not sold separately; call us and we will check what is available.
Titan T8000 Power Nozzle Parts — Frequently Asked Questions
Which belt does the Titan T8000 power nozzle use?
The T8000 power nozzle uses the Titan power nozzle belt 47-3308-08, the same belt as the T9400.
Why is the brush roll on my T8000 not spinning?
A broken or stretched belt is the most common cause. If the belt is good, the power nozzle motor, the circuit board or the power from the lower wand may be at fault.
Should I repair my T8000 power nozzle or buy a new one?
If only the belt, brush roll or lamp board is worn, replace that part. If the housing is cracked or several parts have failed, the complete power nozzle 47-4806-03 is often the better buy.
Shop the Titan T8000 bagless canister vacuum, see all Titan T8000 parts diagrams or browse all Titan vacuum parts. Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.




























