Find genuine Mytee 80-120 parts for the 80-120 Prep Center S all-in-one detail machine. Pick the area of the machine below, click your part on Mytee’s factory drawing, and order it. Can’t find your part? Call us at 763-535-0770.
Prep Center S Parts Diagrams
Housing & Chemical Dispenser
Upper housing, switch plate, the three chemical bottles, dispenser guns, jets, coiled hoses, tubing and air fittings.
Base, Pump & Top Lid
Base, 120 PSI pump and fittings, wheels, axle and casters, heater mount, air regulator, top lid and faucet fill.
Tanks & Vacuum Motor
Solution and recovery tanks, clear lid and gasket, sight elbow, filters, drain valve and the 3-stage vacuum motor.
Heater & Plumbing
The 1,200-watt heater: castings, heating rods, thermostats, relief valve and fittings.
One item in the parts book is not drawn: the G076 mesh filter bag. Item 96 is drawn on the tanks sheet but has no entry in Mytee’s parts list; call us and we will identify it.
Prep Center S Accessories
Mytee supplies the 80-120 with the Air Lite upholstery tool, along with attachments for interior and exterior drying.
About Mytee 80-120 Parts
The Prep Center S combines a heated extractor and a chemical station in one machine. Mytee gives it 12-gallon (approx.) solution and recovery tanks, a 3-stage low-amp vacuum rated at 100 CFM and 130 inches of water lift, a 120 PSI Viton-sealed pump, and a 1,200-watt REAL HEAT heater that reaches 210 degrees. Three chemical bottles run from shop air, each with its own 25-foot coiled hose and adjustable gun. It rolls on 10-inch foam-filled rear wheels and 4-inch locking front casters and runs from one 25-foot 12/3 cord.
Those specifications tell you where 80-120 repairs usually start. Weak suction is usually a sealing part: the clear lid and its gasket, the 6-inch cap and its gasket, the drain valve or a Cuff-Lynx connection. Weak spray starts at the solution tank filter, the quick disconnects and the pump. Cold solution points to the heater rods and thermostats. A dispenser gun that sprays poorly usually needs a new jet.
Shop the Mytee 80-120 Prep Center S machine, browse the full Mytee lineup, see parts for every Mytee machine, or read Mytee’s own 80-120 Prep Center S page. Twin City Vacuum has been selling and servicing cleaning equipment since 1956.
Frequently Asked Questions
What are the most common 80-120 replacement parts?
The parts that wear with use: the chemical dispenser jets (PC12A) and guns (PC12), the 3-quart bottles (PC13), the clear lid and gasket (G030 and G084), the screen and foam filters, the drain valve (H225), the quick disconnects and the wheels and casters. The heater rods (E571) and the vacuum motor (C302LA) are the larger repairs.
How does the 80-120 chemical dispenser work?
Mytee powers it with shop air, 30 PSI maximum. Three bottles each feed a 25-foot coiled hose with an adjustable dispenser gun. The shop-air supply uses brass pneumatic quick disconnects and an H968 0-60 PSI regulator.
Does the 80-120 have a vacuum shut-off float?
No. Mytee’s specifications list no vacuum shut-off switch on the 80-120, so empty the recovery tank before it fills.
What if my part says Call on the parts list?
Mytee does not sell every tank, hose, tube and fastener on its website. Call us at 763-535-0770 with the part number from the list and we will order it for you.
How do I order 80-120 Prep Center S parts or get help?
Open the area of the machine from the cards above, click your part on the diagram or in the table, and add it to your cart. Our staff at 5415 West Broadway, Crystal, MN 55428 can confirm the part against your machine first: call 763-535-0770.
Looking for a specific part? Use the diagrams above to browse the complete parts list, or call 763-535-0770 and we will find it for you.





