Agitator Bearing Holder with Edge Brushes B013-1500

$10.99

Genuine OEM agitator bearing holder with edge brushes, clamping design (part# B013-1500), which supports the agitator end on Simplicity, Riccar, CleanMax and Tornado ultra-lightweight uprights, including the Simplicity S10 and the CleanMax ZM-800. Every model it fits is listed below. Not sure it fits your model? Call us at 763-535-0770.

It fits Simplicity, Riccar, CleanMax and Tornado vacuums; every model is listed under Compatible Models below.

The ZM-800 Agitator Bearing Holder with Edge Brushes (part# B013-1500) is the clamping-design end support that carries the agitator bearing and the edge brushes on the CleanMax ZM-800 commercial battery upright. It locates one end of the agitator (brushroll) and lets it spin freely while the edge brushes sweep debris from along walls and baseboards.


Compatible Models

This genuine part fits the following machines:

  • Simplicity: F3700, F3700.SAND, F3700C, S10CV.4, S10CV.6, S10CV.8, S10D, S10P, S10SAND, SC10CV.10, WONDERP.TAD, WONDERP.TAP
  • Riccar: PRIMAP.TAD, PRIMAP.TAP, R10CV.10, R10CV.6, R10CV.8, R10D, R10P, R10S.2, R10S.4, R10SAND, R17, R50TAP, RSL5, RSL5.SAND, RSL5C
  • CleanMax: ZM-700, ZM-800, ZM-800.2, ZM-800.4
  • Tornado: 97300 CK LW 13/1 ROAM, 97300C CK LW 13/1 ROAM

One part number fits every model listed above across Simplicity, Riccar, CleanMax and Tornado vacuums, including the Simplicity S10 ultra-lightweight uprights and their Riccar R10 SupraLite twins. If your model is not shown, call us at 763-535-0770 with the model number from your vacuum’s label.

This is a genuine OEM part for the CleanMax ZM-800 commercial battery upright.If you are unsure which CleanMax model you have, call 763-535-0770 and we will confirm the correct part before you order.

What the ZM-800 Agitator Bearing Holder does

The bearing holder captures the agitator’s end bearing and clamps into the nozzle so the agitator is held in alignment and turns smoothly under the belt’s drive. Its integrated edge brushes extend the cleaning reach to the very edge of the nozzle, pulling in dirt along walls that the main brushroll would otherwise miss. Because it carries a rotating load all day and its edge brushes drag against baseboards, both the bearing and the brushes are wear items, and the clamping design lets the whole holder be serviced as a unit.


Signs the ZM-800 Agitator Bearing Holder needs replacing

Replace the bearing holder if the agitator end is noisy, rough, or wobbles, if the bearing has seized or developed play, or if the edge brushes are worn down so they no longer reach the floor edges. A squealing or grinding noise from the nozzle end, an agitator that no longer spins freely, or poor edge cleaning all point to a worn bearing holder.


Installation and fit

Power down the machine and open the nozzle to reach the agitator. Release the clamping holder, lift the agitator end out, fit the new bearing holder with edge brushes onto the agitator end, clamp it back into the nozzle, and spin the agitator to confirm it turns freely and quietly. Twin City Vacuum has sold and serviced CleanMax equipment since 1956, and every part is sourced directly from OEM. Browse more CleanMax parts, or learn more at CleanMax.


Frequently Asked Questions

What does the Agitator Bearing Holder do on the CleanMax ZM-800?

It is the clamping end support that carries the agitator’s bearing and the edge brushes, holding the agitator in alignment so it spins smoothly while the edge brushes clean along walls and baseboards.

How do I know if my ZM-800 Agitator Bearing Holder needs replacing?

Replace it if the agitator end is noisy, rough, or wobbles, if the bearing has seized or has play, or if the edge brushes are worn so they no longer reach the floor edges.

What models is the Agitator Bearing Holder (part# B013-1500) compatible with?

It fits the CleanMax ZM-800 agitator family (ZM-800, ZM-800.2, ZM-800.4). Broader CleanMax fitment is not yet listed — call 763-535-0770 and we will verify for your model.

How do I order the Agitator Bearing Holder (part# B013-1500) or get help?

You can add the Agitator Bearing Holder (part# B013-1500) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing CleanMax equipment since 1956 and can help confirm the right part for your machine.



Questions? Call us at 763-535-0770 or visit 5415 West Broadway, Crystal, MN 55428.