5/16 in. Split Lock Washer 01577

$2.99

Genuine OEM 5/16 in. zinc-plated split lock washer (part# 01577) for commercial high-speed burnishers — the standard spring lock washer used under the 5/16 in. hardware on Tornado and Powr-Flite burnisher and floor-machine drawings (see full list below).

The 01577 is a regular-duty 5/16 inch split (helical spring) lock washer in zinc plating. It is the washer specified under the 5/16 inch bolts and nuts on the Brute Force burnisher drawings — shown on the Brute Force 1600 (98458B) drawing and on both Brute Force 2000 glazer drawings (98482B and 98486).

A split lock washer works by spring tension: the gap in the ring bites into the nut face and the mating surface so the joint resists loosening from vibration. On a machine spinning a 20 inch pad at up to 2,000 RPM that matters, because every bolted joint in the chassis sees continuous high-frequency vibration. Once a split washer has been compressed flat it has given up most of its spring and should not be reused — it is the cheapest part on the drawing and the one most worth replacing whenever you take a 5/16 inch joint apart.

Replace the 01577 any time you remove 5/16 inch hardware during a repair, and look for it specifically if you are chasing a bolt that keeps backing out. A washer that has gone flat, lost its gap, cracked at the split, or shows rust-through has nothing left to give. Because it is zinc plated rather than stainless, a washer used in a wet area or on a machine stored damp will corrode first — check condition rather than assuming a used one is still good.

This is a shared piece of hardware rather than a model-specific part: the same 5/16 inch split lock washer is used across the Tornado Brute Force burnisher line and on many other commercial floor machines. If you are not certain which washer belongs at a particular callout on your drawing, call 763-535-0770 with your model and serial number and we will confirm it before you order.

Compatible Models

The 01577 lock washer is a shared part: it fits Tornado and Powr-Flite burnishers and floor machines. The full model list is below.

  • Tornado models:
    • Headmaster 4000 (21 Gallon) w/ Trot-Mop – Series A — 94193
    • 21″ ProGlazer Propane-Powered (11 HP Honda 340CC) – Series A — 97430
    • 24″ ProGlazer Propane-Powered (13 HP Honda 390 CC) – Series C — 97435
    • 28″ ProGlazer Propane-Powered (13 HP Honda 390CC) – Series A — 97450
    • 21″ ProGlazer Propane-Powered (14 HP Onan 390CC) – Series A — 97540
    • 24″ ProGlazer Propane-Powered (14 HP Onan 390CC) w/ Clutch – Series A — 97550
    • 24″ ProGlazer II Propane-Powered (20 HP Onan 782CC) w/ Clutch – Series A — 97555
    • 28″ ProGlazer II Propane-Powered (20 HP Onan 782CC) w/ Clutch – Series A — 97560
    • 24″ ProGlazer Series A — 97570
    • 24″ ProGlazer Series A — 97571
    • 28″ ProGlazer Series-D — 97575
    • 17″ 1.5 HP DS Series w/ Steel Base – Series B — 97580
    • Brute Force 1600 — 98458B
    • Brute Force 2000 High-Speed Glazer — 98482B
    • Brute Force 2000 High-Speed Glazer with Dust Control — 98486
  • Powr-Flite models:
    • C1600-3
    • C1600-T
    • C1600G
    • C202
    • CAS16
    • NM1600
    • NM2000
    • NM2000DC
    • NM202

This part is used on many more Tornado and Powr-Flite machines than we can list here — call 763-535-0770 if yours is not shown and we will confirm it for you.

Frequently asked questions

What does the 5/16 in. split lock washer (part# 01577) do on a burnisher?

It sits under 5/16 inch nuts and bolt heads and uses spring tension to keep the joint from loosening under the continuous vibration of a high-speed burnisher.

How do I know if my 01577 lock washer needs replacing?

If it has been compressed flat, lost the gap at the split, cracked, or corroded, it has lost its spring and will not hold. As a rule, fit a new split lock washer whenever you disassemble a 5/16 inch joint.

Is the 01577 washer stainless steel?

No — it is a zinc-plated regular-duty split lock washer. If your machine works in wet areas, expect the plating to be the limiting factor and inspect for corrosion at each service.

What models is the 5/16 in. split lock washer (part# 01577) compatible with?

It appears on the Tornado Brute Force 1600 (98458B), Brute Force 2000 (98482B) and Brute Force 2000 Dust Control (98486) burnisher drawings, and the same washer is used on many other commercial floor machines.

How do I order the 5/16 in. split lock washer (part# 01577) or get help?

You can add the 5/16 in. split lock washer (part# 01577) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.

Reviews

There are no reviews yet

Be the first to review “5/16 in. Split Lock Washer 01577”

Your email address will not be published. Required fields are marked *