Bolt, 5/16-18 x 3-1/4 in. Hex Cap Screw, Grade 5, Zinc X1377
$1.99
Genuine OEM 5/16-18 x 3-1/4 in. Grade 5 zinc-plated hex cap screw — the long through-bolt that clamps the two blower housing halves together. Fits Tornado and Powr-Flite carpet dryer and air-mover models (see the full list below).
This is the long through-bolt that holds the blower clamshell together. It passes all the way through both housing halves and pulls them into a sealed joint around the scroll. Grade 5 and 3-1/4 inches long are both specification, not incidental: a shorter bolt will not reach its full thread engagement, and a lower-grade substitute will stretch under the clamping load and let the joint work loose again.
Compatible Models
- Tornado: 98774 Windshear 3200
- Powr-Flite: PDS1 Powr-Dryer
- and other Tornado and Powr-Flite air-mover and dryer models — call 763-535-0770 to confirm
A loose housing joint is a problem that announces itself. The two halves chatter against each other at speed, so the machine develops a buzz or rattle that changes with the blower setting, and air leaks out of the seam instead of going down the hose or along the floor. Left alone, the movement works the bolt bosses in the plastic until they crack, and at that point you are replacing a housing instead of a fastener.
Replace these bolts rather than re-using tired ones on a rebuild. Threads that have been cross-threaded or over-torqued into plastic bosses will not develop proper clamp load the second time round. Fit them with the matching 5/16 SAE flat washers (part# X8218), which spread the load across the plastic boss — a bolt run down directly onto the housing will pull through. Tighten evenly, working across the pattern rather than round it, and stop at snug; these are clamping plastic, not steel.
Frequently Asked Questions
What does this through-bolt do on a commercial carpet dryer?
The 5/16-18 x 3-1/4 in. hex cap screw (part# X1377) is the long through-bolt that passes through both blower housing halves and clamps them into a sealed joint around the scroll. Grade 5 material and the 3-1/4 in. length are specification, since the bolt must hold clamp load against a plastic housing.
How do I know if my housing through-bolts need replacing?
Replace them if the housing halves buzz or rattle at speed, if you can feel movement at the seam, if air leaks from the joint, or if the threads are stripped, stretched or cross-threaded. Always fit new bolts on a rebuild rather than reusing over-torqued ones, and use the matching flat washers (part# X8218) so the head does not pull through the plastic boss.
What models is the bolt, 5/16-18 x 3-1/4 in. Hex Cap Screw, Grade 5, Zinc (part# X1377) compatible with?
It fits Tornado 98774 Windshear 3200; Powr-Flite PDS1 Powr-Dryer, and other Tornado and Powr-Flite air-mover and dryer models — call 763-535-0770 to confirm. Compatibility is listed in full in the Compatible Models section on this page.
How do I order the bolt, 5/16-18 x 3-1/4 in. Hex Cap Screw, Grade 5, Zinc (part# X1377) or get help?
You can add the Bolt, 5/16-18 x 3-1/4 in. Hex Cap Screw, Grade 5, Zinc (part# X1377) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.
Need help identifying the right part? Call Twin City Vacuum at 763-535-0770.






Reviews
There are no reviews yet