Flat Washer X8219
$2.99
Genuine OEM flat washer (part# X8219) for Tornado and Powr-Flite commercial high-speed burnishers — the second washer in the pad-drive hardware stack, listed next to washer X8218 on every Brute Force drawing (see full list below).
The X8219 is a flat washer listed on all four drawings in the Brute Force burnisher book — shown on the Brute Force 1600 (98458B), on the Brute Force 2000 (98482B), and on both Brute Force 2000 Dust Control (98486) drawings. On every one of those drawings it sits immediately after the other washer in that group, X8218, which is how the two are told apart: the book lists them as a pair at consecutive callouts, in the hardware around the pad drive and main pulley.
A flat washer has one job and does it in two ways: it spreads the load from a fastener head or nut over a wider area so the clamped part is not dented or crushed, and it gives the fastener a clean, flat, square bearing surface to turn against so the torque you apply actually becomes clamping force instead of friction against a rough casting.
Replace the X8219 when it is dished, galled on one face, burred at the bore, or corroded. Dishing matters more than it looks: a washer that has been pulled into a cone no longer presents a flat face, so the fastener loses preload as the washer flattens back out in service, and the joint is loose a week later. Burrs around the bore are a sign the washer has been spinning under a fastener, which also means the surface underneath has been scored.
Because the Brute Force drawings use several washers of similar appearance at nearby callouts, lay your hardware out in order during a strip-down rather than trusting that they are interchangeable. If you are not sure which washer belongs at which callout, call 763-535-0770 with your model and serial number and we will work through the drawing with you. The part is shared across the Brute Force line and carries no model name. It is a shared part used across Tornado and Powr-Flite machines — see the full list of models below.
Compatible Models
- Tornado models:
- P Series 17″ Floor Machine With Pad Holders (115V) — 97562
- 17″ — 97562B
- P Series 17″ Floor Machine With Pad Holders (230V) — 97563
- P Series 20″ Floor Machine With Pad Holders (115V) — 97564
- 20″ — 97564B
- P Series 20″ Floor Machine With Pad Holders (230V) — 97565
- 28″ ProGlazer Series G — 97575T
- 17″ — 97590
- 20″ 1.5 HP M Series — 97595
- 22″ Marathon 2000 (20 Gallon) – Series H — 98190
- P Series 1600 Glazer (115V) — 98458
- Brute Force 1600 — 98458B
- P Series 1600 Glazer (230V) — 98459
- 17″ 1.5 HP — 98476
- P Series 2000 Glazer (115V) — 98482
- Brute Force 2000 High-Speed Glazer — 98482B
- 20″ 1.5 HP — 98484
- Brute Force 2000 High-Speed Glazer with Dust Control — 98486
- P Series 2000 Glazer (230V) — 98487
- Powr-Flite models:
- C131
- C131G
- C171
- C171HD
- C171HDG
- C171SD
- C172
- C201
- C201HD
- C202
- C202G
- NM1600
- NM171HD
- NM171SD
- NM2000
- NM2000DC
- NM201HD
Frequently asked questions
What does the flat washer (part# X8219) do on a burnisher?
It spreads the clamping load from a fastener over a wider area and gives the fastener a flat, square surface to turn against so applied torque becomes clamping force.
How is the X8219 different from the X8218 washer?
They are different washers listed at consecutive callouts in the same hardware group on every Brute Force drawing — X8218 first, X8219 next. They are not interchangeable, so match the callout number.
How do I know if my X8219 washer needs replacing?
Replace it if it is dished into a cone, galled on a face, burred at the bore, or corroded. A dished washer lets the joint lose preload as it flattens back out in use.
What models is the flat washer (part# X8219) compatible with?
All three Tornado Brute Force burnishers: the 1600 (98458B), the 2000 High-Speed Glazer (98482B) and the 2000 Dust Control (98486).
How do I order the flat washer (part# X8219) or get help?
You can add the flat washer (part# X8219) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.






Reviews
There are no reviews yet