Fuse 3A 62800301
$1.99
Genuine OEM 3 amp fuse (part# 62800301) for Tornado floor scrubbers. It protects a low-current control circuit such as a board supply or sensor feed.
Genuine OEM 3 amp fuse (part# 62800301) for Tornado floor scrubbers — compatible machines are listed below. It is the small rating used on control and signal circuits rather than power ones: a board supply, a sensor feed, a relay coil.
The low rating is what makes this fuse informative. A control circuit draws very little current in normal use — usually a fraction of an amp — so a 3 amp fuse has a great deal of headroom above what the circuit should ever need. When one blows, it is almost never an overload. It is a genuine short: a chafed wire touching the frame, water bridging a connector after a wash-down, or a component that has failed in a way that pulls current it should not.
That means fitting another fuse without looking is a wasted trip. Start where shorts happen: harness sections that flex, loom that passes a frame edge, and connectors low on the machine where water collects. Unplug and inspect rather than relying on a visual sweep — corrosion inside a connector body is invisible from outside.
Never substitute a larger fuse here. The circuits behind a 3 amp fuse are wired in thin conductors and feed electronics; a 10 or 20 amp fuse in this position would let a fault burn a harness or destroy a board before anything opened.
Keep a few on the van. They cost almost nothing, they are the first thing to check when a control function dies, and a machine should never be out of service for a fuse.
Compatible Models
- Tornado 20″ BD 20/11 — 99680
- Tornado 18″ BR 18/11 — 99685
- Tornado BD 22/14 — 99690
- Tornado TS350-W20-U — 99694
- Tornado BR 22/14 — 99695
- Tornado BD 26/14 — 99720
- Tornado BD 26/26 — 99726
- Tornado BD 28/20 — 99728
- Tornado TS550-W28-U — 99729
- Tornado BD 32/26 — 99732
- Tornado BD 26/30 — 99760
- Tornado BR 28/30 — 99765
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado BDSO 20/21 — TS120-S59-U
- Tornado 99694 — TS350-W20-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
- Tornado 99729 — TS550-W28-U
This part is shared across 25 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the electrical layout drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What does the 3 amp fuse (part# 62800301) protect?
A low-current control circuit — a board supply, a sensor feed or a relay coil — rather than a power circuit.
Mine blew. What should I look for?
A genuine short, almost certainly. These circuits draw a fraction of an amp, so 3 amps is far above anything normal. Look at harness sections that flex, loom passing a frame edge, and connectors low on the machine where water collects.
Can I fit a bigger fuse if it keeps blowing?
Absolutely not here. These circuits use thin conductors and feed electronics. A larger fuse would let a fault burn a harness or destroy a board before anything opened.
How do I order the Fuse 3A (part# 62800301) or get help?
You can add the Fuse 3A (part# 62800301) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the fuse 3a (part# 62800301) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet