Hose Clamp 61930002
$6.99
Genuine OEM hose clamp (part# 61930002) for Tornado floor scrubbers. It is the larger clamp that seals the solution hose onto the tank outlet fitting.
Genuine OEM hose clamp (part# 61930002) for Tornado floor scrubbers — compatible machines are listed below. It secures a solution hose onto its fitting in the water filter area. Note the machine uses more than one clamp size here; order by part number, because a clamp that is close but not right either will not pull the hose down evenly or will cut into it.
A hose clamp is cheap, and the thing it prevents is not. On the solution side a weeping joint means air being drawn into the line rather than water squirting out, so the symptom is not a puddle but inconsistent flow that comes and goes — exactly the kind of fault people chase through pumps and valves. On the recovery side a loose clamp costs suction at the squeegee and leaves water on the floor.
What goes wrong is mostly corrosion and over-tightening. A clamp that has rusted will not release its tension evenly and is liable to snap when disturbed; one that has been cranked down hard bites into the hose, and the hose then takes a permanent groove so no clamp will seal it properly again. A clamp that has simply relaxed over time is common too, because the hose underneath cold-flows and takes a set.
Check clamps whenever a line is disturbed and at scheduled service. Replace a clamp that is corroded, has a damaged band or a rounded screw head, or has been removed and refitted several times. Tighten it to seal and no further, and look at the hose end underneath — if it is grooved or hardened, the hose needs attention too.
Compatible Models
- Tornado 20″ BD 20/11 — 99680
- Tornado BD 22/14 — 99690
- Tornado TS350-W20-U — 99694
- Tornado BR 22/14 — 99695
- Tornado BD 26/14 — 99720
- Tornado BD 26/26 — 99726
- Tornado BD 28/20 — 99728
- Tornado BD 32/26 — 99732
- Tornado BD 26/30 — 99760
- Tornado BR 28/30 — 99765
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BD 40/66 — 99790
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado 99694 — TS350-W20-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
This part is shared across 22 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the water filter drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
Where is the hose clamp (part# 61930002) used?
In the water filter area, securing a solution hose onto its fitting. The machine uses more than one clamp size there, so order by part number rather than by eye.
What happens if a solution-side clamp is loose?
You usually do not get a puddle — you get air drawn into the line, so solution flow becomes inconsistent. That is often misdiagnosed as a pump or valve fault.
When should a hose clamp be replaced instead of retightened?
When it is corroded, has a damaged band or a rounded screw head, or has been removed and refitted several times. Check the hose end underneath too — a clamp cranked down hard leaves a permanent groove that no clamp will seal properly again.
How do I order the Hose Clamp (part# 61930002) or get help?
You can add the Hose Clamp (part# 61930002) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the hose clamp (part# 61930002) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet