Hose Clamp 61930009
$3.99
Genuine OEM hose clamp (part# 61930009) for Tornado floor scrubbers. It is the smaller clamp used at several solution-line joints, and the machine carries a number of them.
Genuine OEM hose clamp (part# 61930009) for Tornado floor scrubbers — the machines it fits are listed below. It appears at several joints in the water filter area, so a machine uses more than one and it is worth keeping spares on the van. The assembly also uses a larger clamp under a different part number; order by number, since a clamp that is close but not right will not seal properly.
Its job is simple and unglamorous: hold a flexible hose onto a rigid barb tightly enough that the joint neither leaks nor lets air in. On the solution side the failure that matters is air ingress rather than leakage — the symptom is flow that varies run to run and will not respond predictably to the control, which sends people looking at valves and pumps first.
Clamps of this size fail quietly. They corrode in an environment that is permanently damp, and corrosion makes the band and screw lose tension unevenly and snap when disturbed. They relax as the hose under them cold-flows and takes a set. And they get over-tightened by someone chasing a weep, which cuts into the hose and guarantees the next clamp will leak too.
Treat them as consumables. Replace rather than reuse a clamp that has been off a few times, whose screw head is rounded, or whose band is pitted. Tighten to seal and stop; if a joint still weeps at that point the hose end is the problem, not the clamp. Check the hose for hardening and grooving while you are there, since a tired hose end will defeat a perfect clamp.
Compatible Models
- Tornado BD 26/26 — 99726
- Tornado BD 28/20 — 99728
- Tornado TS550-W28-U — 99729
- Tornado BD 32/26 — 99732
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado BDSO 20/21 — TS120-S59-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
- Tornado 99729 — TS550-W28-U
This part is shared across 16 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the water filter drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
Where is the hose clamp (part# 61930009) used?
At several joints in the water filter area — the machine uses more than one, so it is worth keeping spares. A larger clamp with its own part number is used elsewhere in the same assembly.
Why does a small clamp matter so much on the solution side?
Because the failure is air ingress rather than a visible leak. Flow varies from run to run and stops responding predictably to the control, which usually sends people hunting through valves and pumps first.
Should I retighten or replace?
Replace a clamp that has been off a few times, has a rounded screw head, or has a pitted band. Tighten to seal and stop — if the joint still weeps, the hose end is the problem, and a hardened or grooved hose will defeat a perfect clamp.
How do I order the Hose Clamp (part# 61930009) or get help?
You can add the Hose Clamp (part# 61930009) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the hose clamp (part# 61930009) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet