Hose Clamp 61930010
$3.99
Genuine OEM hose clamp (part# 61930010) for Tornado floor scrubbers. It secures the level hose and fill-side connections on the solution tank.
Genuine OEM hose clamp (part# 61930010) for Tornado floor scrubbers — compatible machines are listed below. On the solution tank assembly it secures hose connections at the tank, including the clear level hose. The machine uses clamps of more than one size; order by part number, because a clamp that is close but wrong either will not pull the hose down evenly or will cut into it.
The job is to hold a flexible hose on a rigid spigot tightly enough that the joint neither leaks out nor draws air in. At the tank, both failure modes matter. A weeping joint at the bottom of a full tank leaks steadily under the head of the liquid above it, wasting chemical and putting water into the machine where the electrics and bearings live. A loose joint on the level hose makes the gauge read wrong, so the operator stops trusting it.
Clamps fail quietly. They corrode in a permanently damp environment, which makes them lose tension unevenly and snap when disturbed. They relax as the hose underneath cold-flows and takes a set. And they get over-tightened by someone chasing a weep, which cuts into the hose and guarantees the next clamp will leak too.
Treat them as consumables. Replace rather than reuse a clamp that has been off a few times, that has a rounded screw head, or whose band is pitted. Tighten to seal and stop. If the joint still weeps at that point, the hose end is the problem — check it for hardening and grooving, since a tired hose end defeats a perfect clamp.
Compatible Models
- Tornado 17″ BD 17/6 Automatic Scrubber — 99617
- Tornado BD 28/20 — 99728
- Tornado TS550-W28-U — 99729
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BDSO 20/21 — TS120-S59-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
- Tornado 99729 — TS550-W28-U
This part is shared across 8 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the solution tank drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
Where is the hose clamp (part# 61930010) used?
On the solution tank assembly, securing hose connections at the tank including the clear level hose. The machine uses clamps in more than one size, so order by part number.
What happens if a tank-side clamp is loose?
At the bottom of a full tank it leaks steadily under the head of liquid above it, wasting chemical and putting water where the electrics and bearings are. On the level hose it makes the gauge read wrong, so the operator stops trusting it.
Retighten or replace?
Replace a clamp that has been off a few times, has a rounded screw head, or has a pitted band — they lose tension unevenly and snap when disturbed. Tighten to seal and stop; if it still weeps, check the hose end for hardening and grooving.
How do I order the Hose Clamp (part# 61930010) or get help?
You can add the Hose Clamp (part# 61930010) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the hose clamp (part# 61930010) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet