Lock Nut 60220803

$1.99

Genuine OEM nylon-insert lock nut (part# 60220803) for Tornado floor scrubbers. It is the most widely used lock nut on the squeegee control linkage, securing the through-bolted pivots along the arms.

Genuine OEM nylon-insert lock nut (part# 60220803), fitted across a very wide range of Tornado floor scrubbers — the full machine list is below. On the squeegee control assembly it is the lock nut that appears most often, used on the through-bolted pivots along the linkage arms wherever a joint must be held captive but still allowed to swing.

Its advantage over a plain nut and lock washer at these positions is that it does not depend on clamp load. A pivot cannot be torqued solid without pinching the bushing and killing the joint movement, so the nut is run up to a held-but-free setting and the nylon insert does the rest. That makes it the correct choice here, and it also makes it a consumable: the insert is cut and deformed by the thread the first time it is fitted and never grips as well again.

Treat them as single-use. The cost of a lock nut is nothing against the cost of a linkage joint coming apart in service, and a nut that has been on and off twice is doing a fraction of the job it was specified for. When rebuilding the squeegee control, fit all new lock nuts and count them against the drawing so none is missed.

What to look for during inspection: a nut you can run down the thread with your fingers has nothing left and must be replaced; so must any showing a crumbling, melted or missing insert, rounded hex corners, or a bore with damaged threads. If several on one machine are loose, that is usually a sign the linkage has been running with worn bushings and cycling further than it should, so check the pivots themselves rather than just renewing the nuts.

This is the genuine Tornado part in the correct size and pattern, so every pivot in the linkage is held the way the design intended.

Compatible Models

  • Tornado BD14/4 Disc Brush Autoscrubber — 99414
  • Tornado 30″ FK3000 Floorkeeper Automatic – Series C — 99430
  • Tornado 17″ BD 17/6 Automatic Scrubber — 99617
  • Tornado 20″ BD 20/11 — 99680
  • Tornado 18″ BR 18/11 — 99685
  • Tornado BD 22/14 — 99690
  • Tornado TS350-W20-U — 99694
  • Tornado BR 22/14 — 99695
  • Tornado BD 26/14 — 99720
  • Tornado BD 26/26 — 99726
  • Tornado BD 28/20 — 99728
  • Tornado TS550-W28-U — 99729
  • Tornado BD 32/26 — 99732
  • Tornado BD 26/30 — 99760
  • Tornado BR 28/30 — 99765
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795
  • Tornado Formerly 99680L — TS120-S45-U
  • Tornado 99680blt — TS120-S53-U
  • Tornado BDSO 20/21 — TS120-S59-U
  • Tornado 99694 — TS350-W20-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U
  • Tornado 99729 — TS550-W28-U

This part is shared across 30 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the lock nut (part# 60220803) do on a Tornado floor scrubber?

It secures the through-bolted pivots along the squeegee control linkage arms, holding each joint captive without clamping it solid so the arms can still swing.

Why not use a plain nut and a lock washer here?

Because a pivot cannot be torqued down hard — that would pinch the bushing and stop the joint moving. A nylon-insert lock nut holds its position without needing clamp load, which is exactly what a swinging joint requires.

Can lock nuts be reused?

No. The nylon insert is cut and deformed by the thread the first time it goes on and grips far less afterwards. Fit all new lock nuts when the squeegee control is rebuilt, and count them against the drawing so none is missed.

How do I order the Lock Nut (part# 60220803) or get help?

You can add the Lock Nut (part# 60220803) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the lock nut (part# 60220803) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Lock Nut 60220803”

Your email address will not be published. Required fields are marked *