Lock Nut INOX 60220602
$1.99
Genuine OEM M6 stainless nylon-insert lock nut (part# 60220602), to UNI 7474, for Tornado floor scrubbers. It is the most-used small lock nut in the squeegee control linkage, holding pivots that must stay captive but still swing freely.
Genuine OEM M6 stainless (INOX) nylon-insert lock nut (part# 60220602), made to UNI 7474, used across a wide range of Tornado floor scrubbers — the full machine list is below. On the squeegee control assembly it is the most frequently used of the small lock nuts, appearing at several pivots along the linkage.
A nylon-insert lock nut is the right fastener for a pivot precisely because it does not rely on clamp load to stay put. At a joint that has to swing, you cannot torque the nut down hard — that would pinch the bushing and stop the arm moving. So the nut is run up until the joint is held but still free, and the nylon insert is what stops it walking off from there. That is a different job from a lock washer, which keeps tension in a joint that is meant to be clamped solid.
The consequence for servicing is simple and often ignored: a nylon-insert nut is a single-use part. The insert is deformed by the thread the first time it goes on, and on the second fitting it grips measurably less. On a pivot where there is no clamp load to help, that reduced grip is all that is holding the joint together. Fit new lock nuts whenever the linkage is rebuilt rather than refitting the old ones.
Check them at service by hand and by eye: a lock nut you can spin down the thread with fingers has lost its insert and must be replaced; so must any that shows a melted, crumbling or missing insert, rounded corners, or corrosion. Stainless is specified because these pivots are permanently in the splash from the squeegee, where a plated nut rusts and seizes.
This is the genuine Tornado part in the correct size, pattern and material, so each pivot is held captive while still swinging the way the linkage needs.
Compatible Models
- Tornado BD14/4 Disc Brush Autoscrubber — 99414
- Tornado 17″ BD 17/6 Automatic Scrubber — 99617
- Tornado 20″ BD 20/11 — 99680
- Tornado 18″ BR 18/11 — 99685
- Tornado TS350-W20-U — 99694
- Tornado BR 22/14 — 99695
- Tornado BD 26/14 — 99720
- Tornado BD 26/26 — 99726
- Tornado BD 28/20 — 99728
- Tornado TS550-W28-U — 99729
- Tornado BD 32/26 — 99732
- Tornado BD 26/30 — 99760
- Tornado BR 28/30 — 99765
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BD 40/66 — 99790
- Tornado BR 40/66 — 99795
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado BDSO 20/21 — TS120-S59-U
- Tornado 99694 — TS350-W20-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
- Tornado 99729 — TS550-W28-U
This part is shared across 28 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What does the lock nut (part# 60220602) do on a Tornado floor scrubber?
It holds pivots in the squeegee control linkage captive without clamping them solid. The joint is run up until it is held but still free to swing, and the nylon insert is what stops the nut walking off from there.
What size and specification is it?
It is an M6 nylon-insert lock nut in stainless (INOX) to UNI 7474. It is the most frequently used of the small lock nuts on the squeegee control assembly.
Can I reuse a lock nut after taking the linkage apart?
No. The nylon insert is deformed by the thread the first time it goes on and grips measurably less the second time. At a pivot there is no clamp load helping to hold it, so that reduced grip is all there is. Fit new lock nuts on every rebuild.
How do I order the Lock Nut INOX (part# 60220602) or get help?
You can add the Lock Nut INOX (part# 60220602) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the lock nut inox (part# 60220602) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.
{“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does the lock nut (part# 60220602) do on a Tornado floor scrubber?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It holds pivots in the squeegee control linkage captive without clamping them solid. The joint is run up until it is held but still free to swing, and the nylon insert is what stops the nut walking off from there.”}},{“@type”:”Question”,”name”:”What size and specification is it?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It is an M6 nylon-insert lock nut in stainless (INOX) to UNI 7474. It is the most frequently used of the small lock nuts on the squeegee control assembly.”}},{“@type”:”Question”,”name”:”Can I reuse a lock nut after taking the linkage apart?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. The nylon insert is deformed by the thread the first time it goes on and grips measurably less the second time. At a pivot there is no clamp load helping to hold it, so that reduced grip is all there is. Fit new lock nuts on every rebuild.”}},{“@type”:”Question”,”name”:”How do I order the Lock Nut INOX (part# 60220602) or get help?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”You can add the Lock Nut INOX (part# 60220602) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.”}}]}






Reviews
There are no reviews yet