Lock Washer 60304002
$1.99
Genuine OEM lock washer (part# 60304002) for Tornado floor scrubbers. It is the small lock washer used at several frame fastening points, keeping bracket and panel fasteners tight under the vibration a scrubber frame carries.
Genuine OEM lock washer (part# 60304002), used across a wide range of Tornado floor scrubbers — the full machine list is below. On the frame assembly it turns up at several positions, under the heads and nuts of the fasteners holding brackets and panels to the chassis.
The frame is where every vibration source on the machine meets: the brush deck, the vacuum motor, the drive wheel and the castors all feed into it, and the loads arrive from different directions at once. That is a harsher environment for a threaded fastener than any single component, and it is why so many of the frame fasteners carry a lock washer rather than relying on torque alone.
These are consumables, not hardware. A lock washer works by elastic deflection, and after it has been compressed and released a few times it has taken a permanent set — it looks the same and does nothing. The test takes a second: a good washer stands proud on a flat surface, a dead one lies flat. Replace every one that comes off during a frame rebuild rather than sorting them on a bench.
Also replace any that are cracked, that show corrosion, or that have bitten so deeply into the bracket beneath that the bracket is marked. That last one is a sign of over-torque, and it is worth checking the fastener and the hole as well, since a wallowed hole will not hold whatever washer you fit.
This is the genuine Tornado part in the correct size, so each frame joint reaches and keeps the clamp load the machine was designed around.
Compatible Models
- Tornado BD14/4 Disc Brush Autoscrubber — 99414
- Tornado 20″ BD 20/11 — 99680
- Tornado 18″ BR 18/11 — 99685
- Tornado TS350-W20-U — 99694
- Tornado BR 22/14 — 99695
- Tornado BD 26/14 — 99720
- Tornado BD 28/20 — 99728
- Tornado BD 26/30 — 99760
- Tornado BR 28/30 — 99765
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BD 40/66 — 99790
- Tornado BR 40/66 — 99795
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado BDSO 20/21 — TS120-S59-U
- Tornado 99694 — TS350-W20-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
This part is shared across 23 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the frame drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What does the lock washer (part# 60304002) do on a Tornado floor scrubber?
It keeps tension on the thread of the fasteners holding brackets and panels to the frame, so they do not work loose under the vibration arriving from the brush deck, vacuum motor, drive wheel and castors.
How do I know if the lock washer (part# 60304002) needs replacing?
Put it on a flat surface: a good one stands proud, a dead one lies flat and is doing nothing. Also replace any that are cracked, corroded, or that have bitten deeply enough to mark the bracket beneath — that last one points at over-torque.
How many does my machine use?
It appears at several positions on the frame assembly, and the count differs between the two frame drawings. Count the positions on your own machine, or call us with your serial number and we will check the drawing for your build.
How do I order the Lock Washer (part# 60304002) or get help?
You can add the Lock Washer (part# 60304002) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the lock washer (part# 60304002) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet