Lock Washer INOX 60508006

$1.99

Genuine OEM stainless lock washer (part# 60508006) for Tornado floor scrubbers. It sits under a nut or screw head in the squeegee control assembly and keeps the joint tight against the constant vibration coming off the brush deck.

Genuine OEM stainless (INOX) lock washer (part# 60508006), used throughout a wide range of Tornado floor scrubbers — the full machine list is below. On the squeegee control assembly it appears at several points in the linkage, fitted under a nut or a screw head wherever a joint has to stay tight but also has to be taken apart for service.

The job is simple and the consequences of skipping it are not. A scrubber squeegee lives in continuous vibration: brush deck chatter, castor rumble, and a blade shearing water off concrete. Plain fasteners in that environment back off, slowly, over weeks. A lock washer keeps load on the thread between the nut and the joint so the fastener stays where it was torqued. When one is missing or flattened, the symptom is not a dramatic failure but a linkage that is mysteriously loose again a fortnight after it was serviced.

The stainless specification matters here too. This part lives in the wettest zone on the machine, permanently splashed with recovery water that may contain detergent and whatever was on the floor. A plated steel washer in that position rusts, and a rusted lock washer both loses its spring and welds itself to the fastener, so the next technician rounds off a nut getting it apart.

Replace rather than reuse. A lock washer works by elastic deflection, and once it has been compressed and released a few times it has taken a permanent set — it will look like a lock washer and act like a flat one. Fit new washers any time the linkage is reassembled, and inspect for the tell-tales: washers that lie flat on a bench instead of standing proud, visible cracking, or discolouration from corrosion.

This is the genuine Tornado part in the correct size and material, so the fastener stack height and the clamp load stay as the machine was designed.

Compatible Models

  • Tornado BD14/4 Disc Brush Autoscrubber — 99414
  • Tornado 20″ BD 20/11 — 99680
  • Tornado 18″ BR 18/11 — 99685
  • Tornado TS350-W20-U — 99694
  • Tornado BR 22/14 — 99695
  • Tornado BD 26/14 — 99720
  • Tornado BD 26/26 — 99726
  • Tornado BD 28/20 — 99728
  • Tornado TS550-W28-U — 99729
  • Tornado BD 32/26 — 99732
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795
  • Tornado Formerly 99680L — TS120-S45-U
  • Tornado 99680blt — TS120-S53-U
  • Tornado BDSO 20/21 — TS120-S59-U
  • Tornado 99694 — TS350-W20-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U
  • Tornado 99729 — TS550-W28-U

This part is shared across 25 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the lock washer (part# 60508006) do on a Tornado floor scrubber?

It sits under a nut or screw head in the squeegee control assembly and keeps tension on the thread, so the fastener does not back off under the continuous vibration coming from the brush deck and the castor.

How do I know if the lock washer (part# 60508006) needs replacing?

Put it on a flat surface. A good one stands proud; one that lies flat has taken a permanent set and is no longer doing anything. Also replace any that are cracked or discoloured by corrosion. The usual field symptom is a linkage that goes loose again a couple of weeks after service.

Why stainless rather than plated steel?

This part lives in the wettest zone of the machine, constantly splashed with recovery water and detergent. A plated washer rusts there, loses its spring, and seizes to the fastener — which means the next technician rounds off the nut trying to get it apart.

How do I order the Lock Washer INOX (part# 60508006) or get help?

You can add the Lock Washer INOX (part# 60508006) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the lock washer inox (part# 60508006) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Lock Washer INOX 60508006”

Your email address will not be published. Required fields are marked *