Nut M4 60210402
$1.99
Genuine OEM M4 nut (part# 60210402) for Tornado floor scrubbers. It is the small nut used behind light bracket and control mountings.
Genuine OEM M4 nut (part# 60210402) for Tornado floor scrubbers — the machine list is below. In the water filter assembly it secures a small fastener behind a bracket or control mounting.
A plain nut is the simplest part on the machine and still worth getting right. Thread pitch, hex size and face flatness all have to match the fastener and the joint; a nut that is close enough to thread on but not actually correct will not seat squarely, will not reach its proper torque, and will chew the screw thread on the way out.
At M4 there is very little thread engaged and very little hex to grip, which changes what tends to go wrong. The hex rounds off easily, and once it has, removing the nut becomes a much bigger job than the part deserves. The thread galls if the nut is run down dry and fast against a stainless screw. And because the clamped area is so small, a joint using a plain nut without a washer will dent its bracket, after which the fastening feels loose a week later with nobody having touched it.
Fit the washer the assembly calls for, run the nut down steadily by hand before putting a wrench on it, and tighten to seat rather than to feel. Replace rather than reuse a nut whose hex is rounded, whose thread drags, or that has been heated or distorted. Where the assembly specifies a lock nut rather than a plain one, do not substitute this part — vibration will undo it.
Compatible Models
- Tornado 20″ BD 20/11 — 99680
- Tornado 18″ BR 18/11 — 99685
- Tornado BD 22/14 — 99690
- Tornado TS350-W20-U — 99694
- Tornado BR 22/14 — 99695
- Tornado BD 26/14 — 99720
- Tornado BD 26/26 — 99726
- Tornado BD 32/26 — 99732
- Tornado BD 26/30 — 99760
- Tornado BR 28/30 — 99765
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado 99694 — TS350-W20-U
This part is shared across 19 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the water filter drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
Where is the M4 nut (part# 60210402) used?
In the water filter assembly, securing a small fastener behind a bracket or control mounting.
Why does a plain nut need replacing at all?
Because the hex rounds off easily at this size, the thread galls if it is run down dry against a stainless screw, and a nut that drags will chew the screw thread on the way out. None of that is worth saving a few cents over.
Can I use this instead of a lock nut?
No. Where the assembly calls for a lock nut, vibration will undo a plain one. Fit the type the assembly specifies, along with the washer it calls for — at M4 the clamped area is small enough that a missing washer dents the bracket and the joint goes loose.
How do I order the Nut M4 (part# 60210402) or get help?
You can add the Nut M4 (part# 60210402) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the nut m4 (part# 60210402) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet