Nut M5 INOX 60210501

$1.99

Genuine OEM M5 stainless nut (part# 60210501) for Tornado floor scrubbers. It is the small stainless nut used at wet joints where a plated nut would rust into the thread.

Genuine OEM M5 stainless (INOX) nut (part# 60210501) for Tornado floor scrubbers — compatible machines are listed below. In the water filter assembly it secures an M5 fastener at a joint that stays wet.

The specification here is about material as much as size. The water filter area is permanently damp: solution passes through it, joints weep a little, and the whole machine gets hosed at the end of a shift. A plated nut in that position loses its coating at the first wrench mark, then rusts into the thread. The part is not expensive; the cost is the next service, when a two-minute job becomes a seized fastener that has to be cut off.

Matching materials matters too. A plated nut on a stainless screw in constant moisture forms a galvanic pair, and the less noble part corrodes faster than either would alone — so the mixed joint is worse than either an all-plated or an all-stainless one.

Stainless has one handling quirk worth knowing: it galls against stainless when it is run down dry and fast. A galled nut seizes part-way and then neither tightens nor comes off, and that is a wrench-and-swearing job on an M5. Run it down by hand first, tighten steadily rather than with an impact driver, and fit the washer the assembly calls for so the nut has a flat face to seat against.

Replace rather than reuse a nut whose hex is rounded, whose thread drags or has galled, or that has been distorted. Where the assembly specifies a lock nut, do not substitute a plain one.

Compatible Models

  • Tornado BD14/4 Disc Brush Autoscrubber — 99414
  • Tornado 20″ BD 20/11 — 99680
  • Tornado 18″ BR 18/11 — 99685
  • Tornado BD 26/14 — 99720
  • Tornado BR 28/30 — 99765
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado Formerly 99680L — TS120-S45-U
  • Tornado 99680blt — TS120-S53-U

This part is shared across 13 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the water filter drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

Why is the nut (part# 60210501) stainless?

Because the water filter area is permanently damp — solution passes through it, joints weep, and the machine gets hosed each shift. A plated nut loses its coating at the first wrench mark and rusts into the thread, turning the next service into a cut-off job.

Can I mix a plated nut with a stainless screw?

Better not to. In constant moisture the two form a galvanic pair and the less noble part corrodes faster than either would alone, so the mixed joint is worse than an all-plated or all-stainless one.

The nut seized half way on. What happened?

Stainless galls against stainless when it is run down dry and fast, and a galled nut will neither tighten nor come off. Run it down by hand first, tighten steadily rather than with an impact driver, and fit the washer the assembly calls for.

How do I order the Nut M5 INOX (part# 60210501) or get help?

You can add the Nut M5 INOX (part# 60210501) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the nut m5 inox (part# 60210501) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Nut M5 INOX 60210501”

Your email address will not be published. Required fields are marked *