Screw 1/4-20 x 1/2 in 00086
$2.99
Genuine Tacony 1/4-20 x 1/2 in Phillips round-head machine screw. Fits Series D, E, F, G and H. In stock in Crystal, MN. Call 763-535-0770. Fits Tornado 93030, Tornado 93031, CleanMax CM-WAV and Powr-Flite PF2030.
The Screw 1/4-20 x 1/2 in (part# 00086) is a genuine Tacony OEM Phillips round-head machine screw used throughout the Tornado CK 3030 wide-area vacuum (Model 93030). and it carries across Series D, E, F, G and H, one of the few fasteners this machine kept unchanged through the whole production run. It is a genuine Tacony OEM part shared across CleanMax, Powr-Flite and Tornado machines — see the full compatibility list below.
At 1/4-20 this is the coarser of the two main thread sizes on the machine, used where a fastening has to carry real load rather than just locate a cover: chassis brackets, motor mounts and the structural joints that hold the deck square. The round head seats against a flat washer rather than pulling into a countersink, which spreads the clamping load over sheet metal instead of concentrating it at a cone.
Replace any that have cammed out at the recess, picked up a damaged or galled thread, or bent. Because 00086 is used in so many positions on this machine it is worth keeping a few in the parts drawer — it is the screw most likely to go missing during a strip-down, and substituting a 1/4-20 of the wrong length or head style in a structural position is exactly how a deck develops a rattle.
Compatible Models for the Screw 1/4-20 x 1/2 in
- Tornado 93030 30″ Clean-Air Carpetkeeper (Wide Area) — Series D, E, F, G and H
- Tornado 93031 30″ Clean-Air Carpetkeeper (Wide Area) 230V
- CleanMax CM-WAV Wide Area Vacuum
- Powr-Flite PF2030 30-Inch Wide Area Commercial Vacuum
These machines are built on the same wide-area platform under different brands and share the great majority of their parts.
Many Tacony fasteners are shared more widely across the Tornado, CleanMax, Riccar, Simplicity and Powr-Flite ranges; if your machine is not listed, call 763-535-0770 and we will confirm before you order.
Twin City Vacuum has been selling and servicing Tacony equipment since 1956 and stocks the genuine 00086 part rather than a hardware-store substitute. Browse the full Tornado 93030 main assembly parts, or read more on the Tornado manufacturer site.
Frequently Asked Questions
What does the Screw 1/4-20 x 1/2 in do on the Tornado 93030?
It is the general-purpose 1/4-20 structural fastener for the machine. It secures brackets, mounts and chassis panels where the joint has to carry load, and it is used across Series D through H.
How many of these does the machine use?
Tacony shows 00086 in multiple positions across the full assembly. The exact count varies by series, so check your machine’s own diagram before ordering a quantity — and order a couple of spares if you are doing a full strip-down.
How do I know if my Screw 1/4-20 x 1/2 in needs replacing?
Replace a screw whose Phillips recess has rounded out, whose thread is stripped or galled, or whose shank is bent. Also replace one that will not draw its bracket tight — if it spins without tightening, check the female thread too, because on this machine the tapped hole usually fails before the screw does.
How do I order the Screw 1/4-20 x 1/2 in (part# 00086) or get help?
You can add the Screw 1/4-20 x 1/2 in (part# 00086) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tacony equipment since 1956 and can help confirm the right part for your machine.
Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.
