Screw M8 x 40 60110818

$1.99

Genuine OEM M8 x 40 mm screw (part# 60110818) for Tornado floor scrubbers. It is a structural fastener used where a heavy component is bolted to the frame.

Genuine OEM M8 x 40 mm screw (part# 60110818) for Tornado floor scrubbers — the machines it fits are listed below. M8 is the size the machine uses where a joint carries real load, and 40 mm is the length for a joint with genuine depth behind it.

In the electrical area that typically means mounting something heavy: a charger, a contactor plate, a battery retainer. Those components are dense, they sit on a machine that vibrates continuously, and they are above or beside things that must not be struck if something comes loose. A fastening here is not holding a cover on.

So check them with a wrench at service rather than by eye. A heavy component whose mounting has backed off a turn starts to move, and movement at that mass wears the mounting hole oval surprisingly quickly — at which point the repair is no longer a fastener.

When one is found loose, replace the lock washer as well. A flattened lock washer has stopped doing its job, and retightening a joint whose washer is dead buys a fortnight. Check the hole too.

Replace the screw if the hex is rounded, if the thread is galled or damaged anywhere along its length, if the shank is bent, or if there is a necked section below the head — a necked screw has been stretched past its yield point and will not hold its clamp load again, however tight it feels.

Tighten steadily. At M8 it is easy to apply enough torque to damage the thread in a casting.

Compatible Models

  • Tornado BD14/4 Disc Brush Autoscrubber — 99414
  • Tornado BD 26/26 — 99726
  • Tornado BD 32/26 — 99732
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C

This part is shared across 9 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the electrical layout drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

Where is the screw (part# 60110818) used?

At structural mountings in the electrical area — a charger, a contactor plate, a battery retainer. These are dense components on a machine that vibrates continuously.

How often should I check these?

At service, with a wrench rather than by eye. A heavy component whose mounting has backed off a turn starts to move, and at that mass the mounting hole wears oval quickly — after which the repair is no longer just a fastener.

What does a necked screw mean?

It has been stretched past its yield point, usually by over-tightening. It will not hold its clamp load again however tight it feels, so replace it rather than reusing it — and replace the lock washer with it.

How do I order the Screw M8 x 40 (part# 60110818) or get help?

You can add the Screw M8 x 40 (part# 60110818) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the screw m8 x 40 (part# 60110818) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Screw M8 x 40 60110818”

Your email address will not be published. Required fields are marked *