Tornado Bracket 30476

The Bracket 30476 is the genuine OEM sheet-metal bracket used on the PS Series professional spotters. The factory parts book lists it plainly as a bracket, without a stated function; on the 98220 in Series F it appears on both the handle assembly and the main assembly, which is the clue to what it is for. It also fits the Tornado PS8226 Spotter 98226, the 230-volt build of the deluxe PS Series spotter.

Compatible Models for the Bracket 30476

• Tornado PS8225 Spotter 98225 — the deluxe PS Series spotter, Series C and Series D & E
• Tornado PS Spotter 98220 — Series C, D, E and F. The current Series G build of the 98220 uses a different part, so check your serial number before ordering.
• Tornado PS8221 Spotter 98221 — Series F, the 230-volt build of the 98220
• Tornado PS8226 Spotter 98226 — the 230-volt build of the deluxe PS Series spotter, Series D & E

Not sure which series your machine is? Call us at 763-535-0770 with the model and serial number and we will confirm it before you order.

Where the Bracket 30476 is used

This is a structural bracket rather than a serviceable mechanism. Appearing on the handle assembly and again on the main assembly of the same machine tells you it is a tie between the two — the kind of folded plate that carries a load path across a joint, locates a component against the chassis, or picks up a fastener that has nothing else to thread into.

We are not going to invent a job for it that the factory did not publish. What we will say is what matters when you order one: a bracket like this is the part that has already failed by the time anything else looks wrong, because it is normally discovered during a repair rather than reported as a fault.

When a bracket like this needs replacing

Replace it when it has cracked at a bend or around a fastener hole, when a hole has elongated so the fastener no longer clamps, when the plate has bent out of true so the parts it locates no longer sit square, or when corrosion has thinned it. Any of those lets the component it carries move under load, and a moving component wears whatever it bears against.

The common cause is a fastener that has been running loose. Once a bolt in sheet metal is loose, the hole takes the load as a hammer blow rather than as clamped friction and the hole wallows out quickly. If you are replacing a bracket because of an elongated hole, replace the fastener and any washer with it and check what loosened it in the first place — very often a failed vibration mount further upstream.

Fitting notes

Photograph the assembly before you take it apart. A plain bracket with two or three holes can usually be fitted more than one way round, and only one of those is right. Transfer the fasteners in the same order and orientation they came out, start every fastener by hand before tightening any of them so the plate can find its position, and only then torque them down. Check that the parts the bracket locates still sit square once it is tight, and confirm nothing it carries is touching a hose or a wire.

If the original bracket was cracked rather than merely loose, look for the reason before fitting the new one. A bracket that cracked once in service will crack again in the same place if whatever was loading it has not been put right.

Twin City Vacuum has been selling and servicing Tornado equipment since 1956 and keeps PS Series spotter parts on the shelf in Crystal, Minnesota.

You can browse every assembly for the deluxe spotter on our Tornado PS Spotter 98225 parts page, and the Tornado PS Spotter 98220 listing covers the 115-volt sibling these parts also serve. Manufacturer specifications are published at tornadovac.com.

Frequently Asked Questions

What does the Bracket 30476 do on the machine?

The factory book lists it as a bracket without stating its function. On the 98220 in Series F it is called out on both the handle assembly and the main assembly, which points to a structural tie across that joint. We would rather tell you that plainly than invent a job for it — call us with your serial number and we will confirm the location in your machine’s own book.

How do I know if this bracket needs replacing?

Look for a crack at a bend or around a fastener hole, a hole that has elongated so the fastener no longer clamps, a plate bent out of true, or corrosion that has thinned it. Any of those lets the part it carries move under load.

Why did my bracket crack or wallow out its hole?

Usually a fastener that had been running loose, which turns clamped friction into repeated hammer blows on the hole. Replace the fastener along with the bracket and find what loosened it — a failed vibration mount upstream is a frequent cause. Fitting a new bracket under the same loading reproduces the failure.

How do I order the Bracket 30476 (part# 30476) or get help?

Call us at 763-535-0770 to order the Bracket 30476 (part# 30476) — this is a factory-order part, so we confirm current pricing and availability when you call and confirm the bracket matches your machine’s series and location. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.