Tornado PS Spotter 98220 Deflector Gasket X2532

The Tornado PS Spotter 98220 Deflector Gasket X2532 is the genuine OEM gasket that seals the recovery tank deflector on the PS Series professional spotter. Tornado’s dealer catalog lists it as “Gasket, For Deflector, 2 Gal. Spotter” — the gasket for the deflector on the 2 gallon spotter, part number X2530.

Compatible Models for the Deflector Gasket

• Tornado PS Spotter 98220 — PS Series professional spotter, 115V, 2 gallon, on the recovery tank assembly

Tornado’s factory cross-reference returns this gasket for the 98220 only, and the part name itself specifies the 2 gallon spotter. The recovery tank uses several different gaskets and they are not interchangeable, so call us at 763-535-0770 with your model and serial number if you are matching a gasket you have already removed.

What this gasket seals

The deflector is the baffle that turns the incoming stream of air, water and soil as it enters the recovery tank, so the water drops out instead of carrying on up the vacuum stack towards the motor. This gasket seals the deflector against its mounting face.

That seal is what forces the incoming stream to go through the baffle rather than around it. A deflector in perfect condition sitting on a failed gasket leaks around its edge, and the stream takes the short cut — which produces exactly the symptoms of a cracked deflector even though the deflector itself is sound. That is the practical reason this inexpensive gasket matters: it is routinely the actual fault when a deflector is suspected.

When to replace it

Replace the gasket if it has hardened and stopped springing back, if it is torn, split or missing a section, if it has compressed permanently flat, or if it has crept out of its seat. A visible gap or witness mark anywhere along the seal is reason enough.

Fit a new one every time the deflector is removed, for any reason. The old gasket has already taken its set around the previous joint and will not seal dependably again, and the cost of the gasket is trivial compared with opening the tank a second time because the reused one leaked. If you are chasing water reaching the vacuum motor, or suction that cuts out on a part-full tank, check this gasket alongside the deflector, the float, the flapper and the stack.

Fitting notes

Clean both faces down to bare material first — dried detergent residue and old gasket material are the usual reasons a new gasket leaks straight away. Seat the gasket without stretching it, then bring the deflector down evenly rather than tightening one side first, so the gasket compresses square instead of being dragged out of position. Make sure the deflector sits fully home on the gasket rather than being pulled into place by its fasteners. Twin City Vacuum has been selling and servicing Tornado equipment since 1956 and keeps PS Series spotter gaskets on the shelf in Crystal, Minnesota.

You can browse every assembly for this machine on our Tornado PS Spotter 98220 parts page, and the manufacturer’s specifications are published at tornadovac.com.

Frequently Asked Questions

What does the Deflector Gasket X2532 do on the Tornado PS Spotter 98220?

It seals the recovery tank deflector against its mounting face, so the incoming stream of air, water and soil is forced through the baffle rather than leaking around its edge.

Should I replace the gasket when I refit the deflector?

Yes, every time. The old gasket has taken a permanent set around the previous joint and will not seal reliably again, and the gasket costs far less than opening the tank a second time.

Which deflector does this gasket fit?

The deflector for the 2 gallon spotter, part number X2530. Tornado names this gasket for that deflector specifically, and the other gaskets in this tank are not interchangeable with it.

How do I order the Deflector Gasket (part# X2532) or get help?

You can add the Deflector Gasket (part# X2532) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.