Trigger Handle X8917
$10.99
Genuine OEM trigger handle (part# X8917) for Tornado and Powr-Flite commercial high-speed burnishers — the moulded trigger the operator closes their hand on, supplied inside the X8911-K handle assembly and separately here.
The X8917 is the trigger handle in the control group of the Brute Force burnishers. It appears on the Brute Force 1600 (98458B) drawing, and inside the complete handle assembly (X8911-K) on the Brute Force 2000 (98482B) and the 29 December 2022 Brute Force 2000 Dust Control (98486) drawings.
It is the primary operator control: the part the hand closes around to run the machine, pivoting on the roll pin (X8918) and returned by the trigger spring (X8916). Because it is held continuously while the machine runs, it also takes the operator’s grip load for hours at a time, and it is the first thing to hit the floor if the machine is dropped on its handle.
Replace the X8917 if it is cracked, if the pin bore has worn oval so the trigger rocks on its pivot, if the moulding is distorted so the trigger binds, or if the surface has worn slick enough to be awkward to hold with a damp hand. A cracked trigger should not be run — if it fails in use the operator loses the control, and a 2,000 RPM machine with no reliable stop is a hazard. Rocking on a worn pin bore gives a vague, sloppy control that gets progressively worse.
Fit a new roll pin (X8918) and trigger spring (X8916) while you have the handle apart; both are inexpensive and both wear alongside the trigger. The part is available individually rather than only inside the complete handle assembly, which keeps a trigger repair to a sensible cost. Note the current 14 July 2025 98486 main body drawing uses a different handle arrangement. Call 763-535-0770 with your model and serial number for confirmation. It is a shared part used across Tornado and Powr-Flite machines — see the full list of models below.
Compatible Models
- Tornado models:
- P Series 17″ Floor Machine With Pad Holders (115V) — 97562
- 17″ — 97562B
- P Series 17″ Floor Machine With Pad Holders (230V) — 97563
- P Series 20″ Floor Machine With Pad Holders (115V) — 97564
- 20″ — 97564B
- P Series 20″ Floor Machine With Pad Holders (230V) — 97565
- 20″ 1.5 HP M Series — 97595
- P Series 1600 Glazer (115V) — 98458
- Brute Force 1600 — 98458B
- P Series 1600 Glazer (230V) — 98459
- P Series 2000 Glazer (115V) — 98482
- Brute Force 2000 High-Speed Glazer — 98482B
- Brute Force 2000 High-Speed Glazer with Dust Control — 98486
- P Series 2000 Glazer (230V) — 98487
- Powr-Flite models:
- C201HD
- C202
- NM1600
- NM171HD
- NM171SD
- NM2000
- NM2000DC
- NM201HD
- NM202
Frequently asked questions
What does the trigger handle (part# X8917) do on a burnisher?
It is the operator control the hand closes on to run the machine. It pivots on the roll pin and is returned by the trigger spring.
How do I know if my X8917 trigger handle needs replacing?
Replace it if it is cracked, if the pin bore has worn oval so the trigger rocks, if it binds, or if the grip surface has worn slick. A cracked trigger should be taken out of service immediately.
What else should I replace with the trigger handle?
The roll pin (X8918) and the trigger spring (X8916). Both are inexpensive, both wear with the trigger, and both are already exposed once the handle is apart.
What models is the trigger handle (part# X8917) compatible with?
The Tornado Brute Force 1600 (98458B), the Brute Force 2000 High-Speed Glazer (98482B) and the Brute Force 2000 Dust Control (98486) as built to its 29 December 2022 drawing.
How do I order the trigger handle (part# X8917) or get help?
You can add the trigger handle (part# X8917) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.






Reviews
There are no reviews yet