Washer, 5/16 in. SAE Flat, Zinc X8218
$2.99
Genuine OEM 5/16 in. washer (part# X8218) for Tornado and Powr-Flite commercial floor equipment — used on all three Tornado Brute Force burnishers (98458B, 98482B, 98486) in the pad-drive hardware. See the full fitment list below.
A flat washer under a bolt head is doing real structural work when the material underneath is moulded plastic. The SAE flat washer spreads the clamping load from the small footprint of the bolt head across a much larger area of the housing boss. Without it, the head concentrates all its force on a ring of plastic barely wider than itself, and on a machine that gets knocked about the bolt eventually pulls straight through the boss.
The same washer is used on all three Tornado Brute Force burnishers: on the Brute Force 1600 (98458B) main assembly drawing, on the Brute Force 2000 (98482B) and on both Brute Force 2000 Dust Control (98486) drawings. On those drawings it is listed immediately before a second washer (X8219) at the next callout, and the two are not interchangeable — order by callout number rather than by appearance.
Compatible Models
This is a shared commercial fastener used across the Tornado and Powr-Flite ranges. It is used across a wide range of Tornado and Powr-Flite machines, including the models below.
- Tornado models:
- P Series 17″ Floor Machine With Pad Holders (115V) — 97562
- 17″ — 97562B
- P Series 17″ Floor Machine With Pad Holders (230V) — 97563
- P Series 20″ Floor Machine With Pad Holders (115V) — 97564
- 20″ — 97564B
- P Series 20″ Floor Machine With Pad Holders (230V) — 97565
- 17″ — 97590
- 20″ 1.5 HP M Series — 97595
- P Series 1600 Glazer (115V) — 98458
- Brute Force 1600 — 98458B
- P Series 1600 Glazer (230V) — 98459
- 17″ 1.5 HP — 98476
- P Series 2000 Glazer (115V) — 98482
- Brute Force 2000 High-Speed Glazer — 98482B
- 20″ 1.5 HP — 98484
- Brute Force 2000 High-Speed Glazer with Dust Control — 98486
- P Series 2000 Glazer (230V) — 98487
- Windshear 3200 — 98774
- Windshear 3200 — 98774MW
- Windshear 3200 — 98786
- ECO 500 AW — 98838
- ECO 500AWH — 98842
- ECO 500AWH Plus — 98846
- ECO 500AW Plus — 98848
- Cascade 20 — 98856
- Cascade 20 OZ — 98860
- Powr-Flite models:
- C131
- C131G
- C171
- C171HD
- C171HDG
- C171SD
- C172
- C201
- C201HD
- C202
- C202G
- NM1600
- NM171HD
- NM171SD
- NM2000
- NM2000DC
- NM201HD
- NM202
This part is used on many more Tornado and Powr-Flite machines than we can list here — call 763-535-0770 if yours is not shown and we will confirm it for you.
SAE pattern is the specification here, not USS. An SAE flat washer has a smaller outside diameter and is thinner than the USS equivalent in the same bore, and it is sized to seat properly inside the recess of the housing boss. A USS washer grabbed from the shop bin may not sit flat in the recess, which leaves the joint rocking on the washer’s edge and defeats the point of fitting one.
These are consumable. Zinc plating gives reasonable corrosion resistance, but washers that have been in service on a water-damage restoration fleet come out dished, rusted or burred from repeated removal, and a dished washer no longer spreads load evenly. Replace them with the through-bolts (part# X1377) as a set when you rebuild a blower housing. This washer is a shared fastener used right across the commercial range, so its full compatibility list is longer than any single machine family.
Frequently Asked Questions
What does this flat washer do on a commercial carpet dryer?
The 5/16 in. SAE flat washer (part# X8218) sits under the blower housing through-bolts and spreads their clamping load across the plastic housing boss. Without it the bolt head concentrates its force on a small ring of plastic and will eventually pull through.
How do I know if my flat washers need replacing?
Replace them if they are dished, rusted, burred or deformed from repeated removal, and fit new ones whenever you replace the through-bolts (part# X1377). A dished washer no longer spreads load evenly, which leaves the joint able to work loose. Use the SAE pattern specified rather than a USS washer, which will not seat correctly in the boss recess.
What models is the washer, 5/16 in. SAE Flat, Zinc (part# X8218) compatible with?
It fits Tornado 98774 Windshear 3200, 98786 Windshear 3200; Powr-Flite PDS1 Powr-Dryer, and other Tornado and Powr-Flite air-mover and dryer models — call 763-535-0770 to confirm. Compatibility is listed in full in the Compatible Models section on this page.
How do I order the washer, 5/16 in. SAE Flat, Zinc (part# X8218) or get help?
You can add the Washer, 5/16 in. SAE Flat, Zinc (part# X8218) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.
Need help identifying the right part? Call Twin City Vacuum at 763-535-0770.






Reviews
There are no reviews yet