Washer 60306005
$1.99
Genuine OEM flat washer (part# 60306005) for Tornado floor scrubbers. It is the general-purpose washer used at several fastening points in the steering group, spreading clamp load across the brackets and covers.
Genuine OEM flat washer (part# 60306005), used across a wide range of Tornado floor scrubbers — the full machine list is below. On the steering wheel assembly it appears at several points, under screws and nuts holding brackets, covers and the column hardware.
Everything in the steering group is clamped rather than pinned, which makes the washers part of how the steering holds its precision. A washer under a fastener spreads that fastener’s load across a wider area of the bracket, so the head does not dig in and start a wear crater. A crater becomes a loose joint; a loose joint in the steering group becomes play the operator feels at the wheel.
Because it appears at several positions, the practical advice is to count rather than assume. When the steering assembly is apart, lay the hardware out in order and check that every washer that came off goes back on. Omission during reassembly is the most common washer fault by a wide margin — far more common than wear.
When they are inspected, replace any that have gone dished rather than flat, that show a bright polished ring on one face, that are noticeably thinner than a new part, or that have started turning with the fastener instead of staying put. These cost very little and the alternative is a bracket that has to be replaced because a fastener head has bitten into it.
This is the genuine Tornado part in the correct diameter and thickness, so each fastener stack reaches its designed height and clamps evenly.
Compatible Models
- Tornado BD14/4 Disc Brush Autoscrubber — 99414
- Tornado 20″ BD 20/11 — 99680
- Tornado 18″ BR 18/11 — 99685
- Tornado TS350-W20-U — 99694
- Tornado BR 22/14 — 99695
- Tornado BD 26/14 — 99720
- Tornado BD 28/20 — 99728
- Tornado TS550-W28-U — 99729
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BR 40/66 — 99795
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado BDSO 20/21 — TS120-S59-U
- Tornado 99694 — TS350-W20-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
- Tornado 99729 — TS550-W28-U
This part is shared across 17 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the steering wheel drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What does the washer (part# 60306005) do on a Tornado floor scrubber?
It spreads the clamp load of a fastener across the bracket or cover beneath it in the steering group, so the fastener head does not dig in and start the wear that turns into play at the steering wheel.
How many does my machine use?
It is used at several points on the steering wheel assembly. Lay the hardware out in order when the assembly is apart and count them, or call us with your serial number and we will check the drawing for your build.
How do I know if the washer (part# 60306005) needs replacing?
Replace any that have gone dished instead of flat, that show a bright polished ring on one face, that are noticeably thinner than a new part, or that turn with the fastener instead of staying put.
How do I order the Washer (part# 60306005) or get help?
You can add the Washer (part# 60306005) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the washer (part# 60306005) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet