Washer 60308003

$1.99

Genuine OEM flat washer (part# 60308003) for Tornado floor scrubbers. It is used at the joint arm and clip pivots of the squeegee control linkage, bearing between the moving arm and the fastener that holds it.

Genuine OEM flat washer (part# 60308003), fitted to a wide range of Tornado floor scrubbers — the machines are listed below. On the squeegee control assembly it is used at the joint arm pivot, alongside the retaining clip and the bushing that carries that joint, and at several other load-bearing points along the linkage.

Where this washer sits, it is doing bearing duty rather than just load spreading. The joint arm turns every time the squeegee is raised, lowered or knocked back, and the washer is the flat face that turning happens against. It is a deliberately sacrificial component: cheap to renew, and standing between the moving arm and a pivot or fastener that is not cheap at all.

Because it is a working surface, it wears in a recognisable pattern. The first sign is a bright polished ring on one face where the arm has been rubbing. Then the washer begins to dish, cupping away from the load. Eventually it thins at the centre and the joint starts to feel loose — at that point the wear has usually begun transferring to the parts either side of it. Catching it at the polished-ring stage is the whole point of inspecting washers at service.

A practical note: this washer appears at more than one point in the linkage and in more than one revision of the assembly, so when ordering it is worth counting the positions on your own machine rather than assuming one. Lay the parts out in order when stripping a joint, and replace every washer that comes out rather than sorting the good from the bad on a bench — the difference is hard to judge by eye and the part costs very little.

This is the genuine Tornado part, in the correct diameter and thickness, so the fastener stack height is unchanged and the pivot keeps the clearance it was designed with.

Compatible Models

  • Tornado BD14/4 Disc Brush Autoscrubber — 99414
  • Tornado 30″ FK3000 Floorkeeper Automatic – Series C — 99430
  • Tornado 20″ BD 20/11 — 99680
  • Tornado 18″ BR 18/11 — 99685
  • Tornado BD 22/14 — 99690
  • Tornado TS350-W20-U — 99694
  • Tornado BR 22/14 — 99695
  • Tornado BD 26/14 — 99720
  • Tornado BD 26/26 — 99726
  • Tornado BD 28/20 — 99728
  • Tornado TS550-W28-U — 99729
  • Tornado BD 32/26 — 99732
  • Tornado BR 28/30 — 99765
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795
  • Tornado Formerly 99680L — TS120-S45-U
  • Tornado 99680blt — TS120-S53-U
  • Tornado BDSO 20/21 — TS120-S59-U
  • Tornado 99694 — TS350-W20-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U
  • Tornado 99729 — TS550-W28-U

This part is shared across 28 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the washer (part# 60308003) do on a Tornado floor scrubber?

It bears between a moving linkage arm and the fastener or pivot holding it in the squeegee control assembly. It spreads clamp load and gives the turning joint a flat, sacrificial face to rub against instead of wearing the arm.

How do I know if the washer (part# 60308003) needs replacing?

Look for a bright polished ring on one face, dishing away from the load, or visible thinning at the centre. The polished ring is the early warning; by the time the joint feels loose, wear has usually started transferring to the parts either side.

How many of these does my machine use?

It appears at more than one point in the squeegee control linkage, and the count differs between revisions of the assembly. Count the positions on your own machine before ordering, or call us with your serial number and we will check the drawing for your build.

How do I order the Washer (part# 60308003) or get help?

You can add the Washer (part# 60308003) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the washer (part# 60308003) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Washer 60308003”

Your email address will not be published. Required fields are marked *