Washer INOX 60306011

$1.99

Genuine OEM stainless washer (part# 60306011) for Tornado floor scrubbers. It spreads fastener load at the wet, exposed joints under the machine where plated washers would rust away.

Genuine OEM stainless (INOX) washer (part# 60306011) for Tornado floor scrubbers — the machine list is below. It is used under the heads and nuts of fastenings at several positions on the machine, including the foot board assembly, where the joint is exposed to water.

The washer’s mechanical job is the usual one: spread the clamping load over a wider area and give the fastener a flat, smooth seat to turn against, so the head does not dig into the bracket and the joint keeps its clamping force. What makes this one specific is the material. Under the deck, solution and recovery water run down, floor grit comes up off the castors, and the machine gets hosed at the end of a shift. A plated washer in that position loses its plating at the first wrench mark, then rusts, swells and bonds the joint together — so the next person to service it is fighting a seized stack instead of undoing three fasteners.

It also matters that the washer matches the fastener it sits under. Stainless hardware with a plated washer sets up a galvanic pair in constant moisture, and the less noble part corrodes faster than either would alone. If the screw is stainless, the washer should be too.

Replace a washer that is dished, cracked, burred around the bore, or badly scored on its bearing face. Dishing means it has yielded and will not clamp as designed. Renew them with the fastener rather than reusing a tired washer in a serviced joint.

This is the genuine Tornado part in the correct bore, outside diameter, thickness and material.

Compatible Models

  • Tornado BD14/4 Disc Brush Autoscrubber — 99414
  • Tornado 17″ BD 17/6 Automatic Scrubber — 99617
  • Tornado 20″ BD 20/11 — 99680
  • Tornado BD 22/14 — 99690
  • Tornado TS350-W20-U — 99694
  • Tornado BR 22/14 — 99695
  • Tornado BD 26/14 — 99720
  • Tornado BD 26/26 — 99726
  • Tornado BD 28/20 — 99728
  • Tornado BD 32/26 — 99732
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BD 33/30 — 99780
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795
  • Tornado Formerly 99680L — TS120-S45-U
  • Tornado 99680blt — TS120-S53-U
  • Tornado BDSO 20/21 — TS120-S59-U
  • Tornado 99694 — TS350-W20-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U

This part is shared across 22 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the foot board drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

Why is the washer (part# 60306011) stainless rather than plated?

Because of where it sits. Under the deck there is solution and recovery water, floor grit off the castors and an end-of-shift hose-down. A plated washer loses its plating at the first wrench mark, then rusts, swells and bonds the joint together.

Can I use a plated washer with a stainless screw?

Better not to. Stainless hardware with a plated washer makes a galvanic pair in constant moisture, and the less noble part corrodes faster than either would on its own. Match the washer to the fastener.

When should it be replaced?

When it is dished, cracked, burred around the bore, or badly scored on its bearing face. Dishing means it has already yielded and will not clamp as designed. Renew washers with the fastener rather than reusing tired ones in a serviced joint.

How do I order the Washer INOX (part# 60306011) or get help?

You can add the Washer INOX (part# 60306011) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the washer inox (part# 60306011) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

{“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”Why is the washer (part# 60306011) stainless rather than plated?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Because of where it sits. Under the deck there is solution and recovery water, floor grit off the castors and an end-of-shift hose-down. A plated washer loses its plating at the first wrench mark, then rusts, swells and bonds the joint together.”}},{“@type”:”Question”,”name”:”Can I use a plated washer with a stainless screw?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Better not to. Stainless hardware with a plated washer makes a galvanic pair in constant moisture, and the less noble part corrodes faster than either would on its own. Match the washer to the fastener.”}},{“@type”:”Question”,”name”:”When should it be replaced?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”When it is dished, cracked, burred around the bore, or badly scored on its bearing face. Dishing means it has already yielded and will not clamp as designed. Renew washers with the fastener rather than reusing tired ones in a serviced joint.”}},{“@type”:”Question”,”name”:”How do I order the Washer INOX (part# 60306011) or get help?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”You can add the Washer INOX (part# 60306011) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.”}}]}

Reviews

There are no reviews yet

Be the first to review “Washer INOX 60306011”

Your email address will not be published. Required fields are marked *