Find genuine Tornado Brute Force burnisher replacement parts for Models 98458B, 98482B and 98486. Can’t find your part? Call us at 763-535-0770.
Pick your machine below to open its exploded parts diagram. Click any numbered dot on the drawing to jump to that part in the table, then click the part to open it in a new tab.
Brute Force 1600 BurnisherModel 98458B · 65 partsShop Parts →
Brute Force 2000 GlazerModel 98482B · 75 partsShop Parts →
Brute Force 2000 Dust ControlModel 98486 · 2 drawingsShop Parts →
Pads & Pad DriverFits all three machinesShop Parts →The Tornado Brute Force burnisher line covers three high-speed polishing machines built on the same chassis family: the Brute Force 1600 (Model 98458B), the Brute Force 2000 High-Speed Glazer (Model 98482B), and the Brute Force 2000 High-Speed Glazer with Dust Control (Model 98486). Because all three share one parts diagram, roughly half of the parts on any one drawing also fit the other two machines — handles, switches, cord sets, pad drivers, wheels, bearings and hardware carry across. The pad driver, pads and retainers are common to the whole line, which is why they live on a single shared page rather than being repeated three times.
How to find the right Tornado Brute Force burnisher parts
Start with the model number stamped on your machine’s data plate, not with the name on the handle. All three Brute Force burnishers were sold under similar “1600” and “2000” badging, and the 98482B and 98486 are the same glazer with and without the dust-control shroud — so the badge alone will not tell you which parts diagram applies. The data plate is on the motor housing or the rear of the body and carries the model number (98458B, 98482B or 98486) and the serial number. Once you have it, open that machine’s page above and work from the numbered drawing.
The parts that wear out first on a high-speed burnisher are predictable. Pads and the pad driver go first and are consumables — a glazed or loaded pad is the usual cause of swirl marks and poor gloss, and a worn pad-retainer center lock lets the pad walk off under load. Next are the wheels and the transport axle, which flat-spot from being dragged across thresholds, and the power cord and strain relief, which fail where the cord leaves the handle. Electrically, the on/off switch, capacitor and motor brushes are the common failures: a machine that hums but will not spin up, or that trips the breaker on start, is nearly always one of those three rather than the motor itself. Vibration and noise at speed usually trace to the motor-shaft bearings or a bent pad driver, both of which are serviceable parts on these drawings.
Several components on the Brute Force drawings — pad drivers, retainers, wheels, switches and cord assemblies — are also used on the matching Powr-Flite high-speed burnishers, so the part number is the thing to match, not the brand on the hood. If the number on your old part is worn off, call us with the model and serial number and we will read it off the drawing with you.
Twin City Vacuum has sold and serviced commercial floor equipment from 5415 West Broadway, Crystal, MN 55428 since 1956. We stock and order genuine Tornado parts, and if a part is not listed with a price on these pages it means it is special-order — call 763-535-0770 and we will quote it and confirm fitment before you buy. For other Tornado equipment, see our full Tornado parts hub, and for machine specifications and manuals see tornadovac.com.
Tornado Brute Force burnisher parts — frequently asked questions
Which Tornado Brute Force burnisher models do these parts pages cover?
These pages cover the Brute Force 1600 (Model 98458B), the Brute Force 2000 High-Speed Glazer (Model 98482B), and the Brute Force 2000 High-Speed Glazer with Dust Control (Model 98486). All three share one parts diagram, and the pads and pad driver are common to all three.
Do 98482B and 98486 use the same parts?
Largely, yes — the 98486 is the dust-control version of the 98482B glazer and shares the motor, handle, wheels and pad drive. The 98486 adds its own dust-control shroud, filter and skirt parts that the 98482B does not have, and the 98486 is covered by two dated drawings whose parts lists differ slightly. Work from your machine’s own page rather than assuming the two are interchangeable.
Is the Brute Force 1600 (98458B) still supported?
Yes. The 98458B is no longer in Tornado’s current machine line-up, but its parts diagram is still live and the parts are still sold. Its page is above with the full numbered drawing.
How do I know which pad and pad driver my burnisher takes?
The pad driver and pad sizing are shared across the Brute Force burnisher line and are listed on the Pads & Pad Driver page above, together with the retainer and center lock. If you are unsure which grade of pad you need for your floor finish, call 763-535-0770 — pad choice depends on the finish and the gloss you are after, not just the machine.
A part on the table shows “call us” instead of a price — can I still get it?
Yes. A “call us” row means the part is special-order rather than stocked with a published price. Call 763-535-0770 with the part number from the table and we will quote it, check availability and confirm it is right for your model and serial number before you order.
How do I order Tornado Brute Force burnisher parts or get help identifying one?
Open your machine’s page above, click the numbered dot on the drawing or the row in the table, and add the part to your cart. If you cannot identify the part, call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has serviced commercial floor machines since 1956 and can confirm the right part from your model and serial number.
Need a part that is not on any of these drawings, or not sure which Brute Force machine you have? Call 763-535-0770 or see the full Tornado parts hub for other Tornado floor machines, burnishers, sweepers and extractors.
Looking for the machine itself? See the Tornado Brute Force 2000 High-Speed Burnisher listing, or call 763-535-0770.
