Mytee HP90 Stingray Parts — Models HP90 and HP90-SS

Find genuine Mytee HP90 parts for the HP90 Stingray heated automotive detailing extractor, Model HP90 and Model HP90-SS. Pick the area of the machine below, click your part on Mytee’s factory drawing, and order it. Can’t find your part? Call us at 763-535-0770.

Which HP90 Do I Have?

Mytee builds the HP90 Stingray as the HP90 and the HP90-SS. The HP90-SS is the same machine supplied with a stainless steel upholstery tool instead of the Air Lite tool, and both models share one Mytee parts book, so every part on these pages fits both. Check the model label on the machine if you are not sure.

HP90 Stingray Parts Diagrams

Mytee HP90 Stingray solution tank and plumbing parts diagram

Solution Tank & Plumbing

Solution tank and lid, faucet fill, handle, quick disconnect, filter strainer and the brass fittings that feed the pump.

Mytee HP90 Stingray base, pump and heater plumbing parts diagram

Base, Pump & Heater Plumbing

Base, 120 PSI pump, heater mounting and the fittings between the pump, heater and quick disconnect.

Mytee HP90 Stingray recovery tank and vacuum motor parts diagram

Recovery Tank & Vacuum Motor

Recovery tank, clear lid and gasket, float shut-off, 3-stage vacuum motor, switches, casters and power cord.

Mytee HP90 Stingray A907 heater parts diagram

A907 Heater

The 1,200-watt A907 heater: casting, two 600-watt heating rods, thermostats and fittings.

HP90 Stingray Accessories

Mytee supplies the HP90 with the Air Lite upholstery tool, a 15-foot hose combo and a 2-inch Cuff-Lynx reducer; the stainless steel 8400 tool is also available as an alternative.

About Mytee HP90 Parts

Mytee designed the Stingray for automotive detailers: two 5-gallon tanks, a 3-stage vacuum rated at 100 CFM and 130 inches of water lift, a 120 PSI pump delivering 1.3 gallons per minute, and a 1,200-watt heater that brings solution up to 210 degrees. It rolls on 3-inch locking casters and runs from a 25-foot 12/3 power cord, with a float switch that shuts the vacuum off when the recovery tank is full.

Those specifications tell you where HP90 repairs usually start. Weak suction is almost always a sealing part: the clear lid and its gasket, the drain valve, a vacuum motor gasket or a Cuff-Lynx connection. Spray problems start at the solution strainer, the quick disconnects and the pump. Cold solution points to the A907 heater, which has two replaceable 600-watt rods. If the vacuum stops on its own, check the float switch (E373) and its relay (E632) before the motor.

Shop the Mytee HP90 Stingray machine, browse the full Mytee lineup, see parts for every Mytee machine, or read Mytee’s own HP90 Stingray page. Twin City Vacuum has been selling and servicing cleaning equipment since 1956.

Frequently Asked Questions

Which HP90 do I have, the HP90 or the HP90-SS?

Mytee builds the HP90 Stingray as the HP90 and the HP90-SS. The HP90-SS is the same machine supplied with a stainless steel upholstery tool. Both use the same Mytee parts book, so every part on these pages fits both. The model number is on the machine label.

What are the most common HP90 replacement parts?

The parts that wear with use: the 7-inch vacuum lid gasket (G091), the screen mesh filter (G097), the vacuum motor gaskets (G004), the Cuff-Lynx connectors (H135V, H124V and H122V), the drain valve (H225) and the quick disconnects. The 1,200-watt heater rods (E571) and the vacuum motor (C302LA) are the larger repairs.

How hot does the HP90 heater get?

Mytee rates the HP90 heater at 1,200 watts with solution up to 210 degrees. The A907 heater and its rods have their own diagram.

What if my part says Call on the parts list?

Mytee does not sell every screw, washer and nut on its website. Call us at 763-535-0770 with the part number from the list and we will order it for you.

How do I order HP90 Stingray parts or get help?

Open the area of the machine from the cards above, click your part on the diagram or in the table, and add it to your cart. Our staff at 5415 West Broadway, Crystal, MN 55428 can confirm the part against your machine first: call 763-535-0770.

Looking for a specific part? Use the diagrams above to browse the complete parts list, or call 763-535-0770 and we will find it for you.