CleanMax Zoom Pigtail Power Cord D434-3814
$31.99
Genuine CleanMax D434-3814 pigtail power cord: the short handle-base power lead the CMPS-EXT30 extension cord plugs into on corded Zoom ZM-400 and ZM-600 commercial uprights.
The CleanMax Zoom pigtail power cord (part# D434-3814) is the short factory-wired power lead that exits the base of the handle on a corded CleanMax Zoom commercial upright and gives the machine the socket its detachable extension cord plugs into. It is the fixed half of the two-piece cord system used on these vacuums, and it wires directly into the machine’s switch and motor circuit.
Compatible Models for the CleanMax Zoom Pigtail Power Cord
- CleanMax Zoom ZM-400
- CleanMax Zoom ZM-600
The D434-3814 pigtail is used on the corded CleanMax Zoom ZM-400 and ZM-600 uprights, which pair this short lead with the separate CMPS-EXT30 extension cord rather than a single fixed cord. If you are unsure which Zoom model you own, call us at 763-535-0770 and we will confirm the correct pigtail before you order.
What the D434-3814 Pigtail Cord Does
Instead of running one long cord straight into the vacuum, the Zoom commercial design splits the cord in two: a short pigtail permanently wired to the machine, and a long detachable extension cord that snaps onto it. The pigtail carries current from that connection point into the on/off switch and motor. Splitting the cord this way lets an operator swap a damaged extension cord in seconds, while the pigtail itself only needs replacing if the lead or its connector is damaged.
Signs You Need a New Pigtail Cord
Replace the D434-3814 if the vacuum cuts out or flickers when you flex the cord where it enters the handle, if the outer jacket is split or the copper is exposed at that point, or if the socket that receives the extension cord is cracked, loose, melted, or scorched. Because the pigtail is hard-wired into the machine, a damaged one is both a power-reliability and a safety issue and should be replaced promptly.
Installation and Fit
Replacing the pigtail involves opening the handle to disconnect the lead from the switch and motor wiring, so it is a job best done by someone comfortable with vacuum wiring or by a service shop. As a genuine CleanMax lead it matches the gauge, length, and connector the Zoom platform requires. Our technicians at 5415 West Broadway, Crystal, MN 55428 have been servicing CleanMax equipment since 1956 and can install it for you. Browse more CleanMax Zoom handle and bag parts, or learn more at CleanMax.
Frequently Asked Questions
What does the CleanMax Zoom pigtail power cord do on the ZM-400 and ZM-600?
It is the short factory power lead at the base of the handle that carries current from the detachable extension cord into the vacuum’s wiring and switch. The long CMPS-EXT30 extension cord plugs into it.
How do I know if my D434-3814 pigtail cord needs replacing?
Replace it if the machine loses power or flickers when the cord is wiggled near the handle, if the jacket is cracked or the wire is exposed where it exits the handle, or if the connector where the extension cord plugs in is loose, melted, or scorched.
What models is the CleanMax Zoom pigtail power cord (part# D434-3814) compatible with?
It fits the corded CleanMax Zoom ZM-400 and ZM-600 commercial uprights. Call 763-535-0770 if you need help confirming your model before ordering.
How do I order the CleanMax Zoom pigtail power cord (part# D434-3814) or get help?
You can add the CleanMax Zoom pigtail power cord (part# D434-3814) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing CleanMax equipment since 1956 and can help confirm the right part for your machine.
