Brush Motor 46200460
$1,106.99
Genuine OEM brush motor (part# 46200460) for Tornado floor scrubbers. It is the gear motor that drives one scrub brush; a 27-inch or 28-inch twin-disc machine uses two.
Genuine OEM brush motor (part# 46200460) for Tornado floor scrubbers — compatible machines are listed below. It is the gear motor mounted on the brush deck that turns one brush or pad driver. A twin-disc machine carries two of them, one per brush, so a machine that is scrubbing noticeably better on one side than the other is usually telling you about this part.
The motor does more than spin. Through its gearbox it sets the brush speed and, just as importantly, supplies the torque that lets a brush keep cutting when it is loaded into soil rather than skating over it. That is why a failing motor shows up as poor cleaning before it shows up as a dead machine: the brush still turns, but it stalls or slows the moment real down-pressure is applied, and the floor behind the machine stops coming clean.
Watch for the usual symptoms. A motor drawing more current than it should will trip the brush circuit, often part-way through a run once it is hot. Worn brushes inside the motor cause intermittent running and arcing. Bearing wear shows up as a growl or rumble that changes with speed, and gearbox wear as a knock under load or play you can feel at the brush hub with the machine off. Water ingress is the other classic killer on a scrubber — this motor lives directly above the wettest part of the machine.
Before replacing one, rule out what loads it: a brush or pad driver that is binding, a seized hub, or deck geometry that is pressing one side harder than the other. A new motor fitted to a mechanical problem will fail the same way.
This is the genuine Tornado motor with the correct voltage, gear ratio, shaft and mounting.
Compatible Models
- Tornado BD 28/20 — 99728
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado TS530-W26-U
- Tornado TS530-W30-U
This part is shared across 4 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the brush base transmission drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What does the brush motor (part# 46200460) do?
It is the gear motor on the brush deck that drives one scrub brush or pad driver, setting both the brush speed and the torque available to keep the brush cutting under down-pressure. A twin-disc machine uses two.
One side of my machine is not cleaning as well as the other. Is this the motor?
Often, yes. A failing brush motor usually shows up as poor cleaning before it shows up as a dead machine — the brush still turns but slows or stalls as soon as down-pressure is applied, so the floor behind that side stops coming clean.
What should I check before replacing the brush motor?
Whatever is loading it: a brush or pad driver that is binding, a seized hub, or deck geometry pressing one side harder than the other. Also check for water ingress, since this motor sits above the wettest part of the machine. A new motor fitted to a mechanical problem fails the same way.
How do I order the Brush Motor (part# 46200460) or get help?
You can add the Brush Motor (part# 46200460) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the brush motor (part# 46200460) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet