Bushing 47103090

$20.99

Genuine OEM bushing (part# 47103090) for Tornado stand-on and walk-behind floor scrubbers. It is the bearing sleeve in the joint arm pivot of the squeegee control linkage, the hinge the squeegee swings on when it breaks away from an obstacle.

Genuine OEM bushing (part# 47103090), fitted across a broad range of Tornado stand-on and walk-behind scrubbers — the full list of machines is below. On the squeegee control assembly it carries the joint arm pivot, the hinge where the jointed arm meets the squeegee carriage, secured by a long through-screw with a washer under the head.

This is the busiest pivot in the whole squeegee control group. It moves every time the actuator raises or lowers the squeegee, and it also takes the shock load whenever the squeegee swings back off a pallet leg, a dock edge or a floor drain. That combination of constant small movement and occasional hard impact is what wears it, and it is why this bushing is a heavier and more substantial part than the plain pivot sleeves elsewhere in the same linkage.

Worn-bushing symptoms show up in the floor behind the machine before they show up as noise. The squeegee starts to hang slightly off square, so one end of the blade loads harder than the other and leaves a wet edge on that side. Operators often respond by flipping or replacing the blade, which helps for a week or two and then the stripe comes back. Other signs are a knock you can hear when the squeegee drops, visible rocking in the joint when you move the squeegee by hand, and a squeegee that no longer returns to centre cleanly after a break-away.

When replacing it, clean the bore thoroughly and inspect the arm and the carriage ear for ovalling. Check the through-screw too: a bushing that has been running loose will have let the screw take some of the load and it may be scored or slightly bent. Reassemble so the joint swings freely under its own weight — a pivot that is pinched will wear the new bushing fast.

This is the genuine Tornado part, so the bore and the shoulder match the original and the linkage geometry is unchanged. On a squeegee, geometry is everything: the blade angle set by this joint is what decides whether the machine leaves a dry floor.

Compatible Models

  • Tornado TS350-W20-U — 99694
  • Tornado BR 22/14 — 99695
  • Tornado BD 26/14 — 99720
  • Tornado BD 26/26 — 99726
  • Tornado BD 28/20 — 99728
  • Tornado TS550-W28-U — 99729
  • Tornado BD 32/26 — 99732
  • Tornado BD 26/30 — 99760
  • Tornado BR 28/30 — 99765
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795
  • Tornado 99694 — TS350-W20-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U
  • Tornado 99729 — TS550-W28-U

This part is shared across 21 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the bushing (part# 47103090) do on a Tornado floor scrubber?

It is the bearing sleeve in the joint arm pivot of the squeegee control linkage — the hinge where the jointed arm meets the squeegee carriage. It lets the squeegee swing as it is raised, lowered and pushed back off obstacles, and it absorbs the wear that would otherwise fall on the arm and the through-screw.

How do I know if the bushing (part# 47103090) needs replacing?

Look at the floor first. A wet stripe along one edge of the lane that comes back soon after a new blade is fitted usually means the squeegee is hanging off square at this joint. Confirm it by moving the squeegee by hand with the machine parked and watching for rocking or knock at the joint.

Why is this bushing more expensive than the other pivot bushings in the same assembly?

It carries the busiest and most heavily loaded pivot in the group. It moves on every raise and lower and also takes the shock when the squeegee breaks away from an obstacle, so it is a larger, heavier part than the plain sleeves used elsewhere in the linkage.

How do I order the Bushing (part# 47103090) or get help?

You can add the Bushing (part# 47103090) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the bushing (part# 47103090) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Bushing 47103090”

Your email address will not be published. Required fields are marked *