Bushing 47106030

$14.99

Genuine OEM bushing (part# 47106030) for Tornado stand-on and walk-behind floor scrubbers. It is the bearing sleeve at the spring-anchor pivot of the squeegee control linkage, where the break-away spring pulls against the arm.

Genuine OEM bushing (part# 47106030), used on a range of Tornado stand-on and walk-behind floor scrubbers — the machines it fits are listed below. On the squeegee control assembly it sits at the pivot next to the break-away spring, where the spring tension is reacted into the linkage arm and held by a nut.

This bushing lives under constant preload rather than constant motion. The spring beside it is always pulling, so the bushing is squeezed against one side of its bore the entire time the machine is in service, and it only moves when the squeegee breaks away or is raised. That loading pattern wears a bushing differently from a plain hinge: instead of going evenly round, it goes oval on one face, and the symptom is a squeegee that no longer returns to exactly the same position after it has been knocked.

Watch for a squeegee that comes back from a break-away slightly off centre, a change in how firmly the squeegee is held down, a clicking or tapping from the linkage as the spring takes up slack, or uneven blade wear that appears gradually rather than suddenly. If the spring has been replaced and the squeegee still does not sit true, this bushing is the usual reason.

Replace it with the spring tension released, not with the spring loaded — trying to drive the pivot out against the spring is how the arm gets bent. Clean the bore, check the mating face for a wear step, and look at the spring itself while you have it off; a spring that has been working through a loose bushing has usually been cycling further than it should and may be tired. Set the nut so the joint is held but still free to swing.

Because this is the genuine Tornado part, the bore and length match the original, so the spring preload and the rest position of the squeegee stay exactly where the factory set them.

Compatible Models

  • Tornado BD 26/30 — 99760
  • Tornado BR 28/30 — 99765
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795

This part is shared across 10 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the bushing (part# 47106030) do on a Tornado floor scrubber?

It is the bearing sleeve at the spring-anchor pivot in the squeegee control linkage. It carries the load from the break-away spring into the arm and lets the joint swing when the squeegee is raised or knocked off an obstacle.

How do I know if the bushing (part# 47106030) needs replacing?

The usual sign is a squeegee that does not return to exactly the same position after it has been knocked. Other symptoms are a change in how firmly the squeegee is held down, a tap or click from the linkage as the spring takes up slack, and blade wear that becomes uneven gradually.

I already replaced the spring and the squeegee still sits off true. What now?

That is the classic sign that the problem is this bushing rather than the spring. Because the spring is always pulling on it, the bushing wears oval on one face, and the squeegee then settles slightly off centre no matter how good the spring is.

How do I order the Bushing (part# 47106030) or get help?

You can add the Bushing (part# 47106030) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the bushing (part# 47106030) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Bushing 47106030”

Your email address will not be published. Required fields are marked *