Cap 62010002

$1.99

Genuine OEM cap (part# 62010002) for Tornado floor scrubbers. It closes off a port on the vacuum assembly, keeping the recovery circuit sealed so the motor pulls its air through the squeegee and not through an open fitting.

Genuine OEM cap (part# 62010002) for Tornado floor scrubbers — the full machine list is below. On the vacuum assembly it closes a port in the motor housing area, and like every other seal in a recovery circuit its whole purpose is to make sure the vacuum motor draws its air through the squeegee.

Small closures like this are the components most often lost and least often ordered. One goes missing during a service, the machine still runs, and the loss of suction that follows gets blamed on blades or on the motor. A machine with an open port is a machine with a permanent air leak in the exact circuit it depends on, and no amount of new blades will fix it.

Check it at service. Replace it if it is cracked, distorted, no longer grips its port firmly, or has hardened so it cannot seat properly. If it comes off in normal running, that is itself a failure — a cap that will not stay put is not sealing the rest of the time either. And if the cap is simply missing, fit a new one rather than improvising with tape; tape fails wet, and it fails exactly where nobody is looking.

It is worth keeping one on the shelf. The part costs very little, the machine loses real cleaning performance without it, and the fault is almost impossible to diagnose by ear — there is nothing to hear, just a machine that leaves a film behind.

This is the genuine Tornado part, sized to its port so it seats and seals properly rather than approximately.

Compatible Models

  • Tornado BD 28/20 — 99728
  • Tornado TS550-W28-U — 99729
  • Tornado BD 26/30 — 99760
  • Tornado BR 28/30 — 99765
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U
  • Tornado 99729 — TS550-W28-U

This part is shared across 13 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the vacuum drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the cap (part# 62010002) do on a Tornado floor scrubber?

It closes a port on the vacuum assembly, keeping the recovery circuit sealed so the vacuum motor pulls its air through the squeegee rather than in through an open fitting.

How do I know if the cap (part# 62010002) needs replacing?

Replace it if it is cracked, distorted, hardened, no longer grips its port firmly, or comes off during normal running. If it is missing entirely, fit a new one rather than improvising with tape, which fails once it is wet.

Can a missing cap really cost suction?

Yes, and it is one of the harder faults to spot. An open port is a permanent air leak in the recovery circuit, so the machine leaves a film behind no matter how good the squeegee blades are. There is no noise to lead you to it.

How do I order the Cap (part# 62010002) or get help?

You can add the Cap (part# 62010002) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the cap (part# 62010002) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Cap 62010002”

Your email address will not be published. Required fields are marked *