Handwheel 61710003

$9.99

Genuine OEM handwheel (part# 61710003) for Tornado floor scrubbers. It is the hand knob on the squeegee tilt adjuster — the control the technician turns to set how far the squeegee blade leans back against the floor.

Genuine OEM handwheel (part# 61710003) for Tornado floor scrubbers — see the full list of machines below. On the squeegee control assembly it threads onto the adjuster bar and is the control an operator or technician actually puts a hand on when setting squeegee blade angle. Turn it one way and the blade leans further back; turn it the other and it stands more upright.

Blade angle is the single most important adjustment on a scrubber squeegee. Too upright and the blade scrapes rather than wipes, wearing the edge square in days. Too far back and the blade folds under and rides over the water instead of shearing it off the floor. The handwheel is what makes that a thirty-second adjustment instead of a wrench job, which is why it matters that it works properly rather than being seized or stripped.

Handwheels fail in predictable ways. The knob spins without moving the adjuster, which means the thread inside has stripped. It cracks across a spoke or the rim, usually after the machine has been knocked against a wall or a rack leg. Or it corrodes onto the bar so it cannot be turned by hand at all, and the next person reaches for pliers and finishes it off. Any of these is a replace, because an adjuster you cannot turn is an adjustment nobody makes, and the blades pay for it.

When fitting a new one, clean and inspect the threaded bar first. A handwheel that stripped usually did so because the bar was damaged or because grit had packed into the thread, and a new knob on a bad bar will strip again. Run the knob down the full length of the bar by hand before refitting to check the thread is clean all the way.

This is the genuine Tornado part, so the thread form and the knob diameter match the original and the adjuster has the same feel and the same range of travel as it did new.

Compatible Models

This part is shared across 8 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the handwheel (part# 61710003) do on a Tornado floor scrubber?

It is the hand knob on the squeegee tilt adjuster. Turning it changes how far the squeegee blade leans back against the floor, which is the adjustment that decides whether the machine leaves a dry lane or a wet film.

How do I know if the handwheel (part# 61710003) needs replacing?

Replace it if the knob spins without moving the adjuster (stripped thread), if it is cracked across a spoke or the rim, or if it has corroded onto the bar so firmly that it cannot be turned by hand. Reaching for pliers on a seized handwheel almost always destroys it.

My new handwheel stripped quickly. Why?

Almost always the threaded bar it runs on. A damaged or grit-packed bar will chew a fresh knob in short order. Clean and inspect the bar, and run the new knob down its full length by hand before refitting to check the thread is clean end to end.

How do I order the Handwheel (part# 61710003) or get help?

You can add the Handwheel (part# 61710003) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the handwheel (part# 61710003) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Handwheel 61710003”

Your email address will not be published. Required fields are marked *