Lock Nut 60221002

$1.99

Genuine OEM nylon-insert lock nut (part# 60221002) for Tornado floor scrubbers. On the squeegee control assembly it locks the tilt adjuster, holding the squeegee blade angle against vibration between services.

Genuine OEM nylon-insert lock nut (part# 60221002), used on a range of Tornado floor scrubbers — the full machine list is below. On the squeegee control assembly it belongs to the tilt adjuster group, running on the threaded bar with its washer and locking the setting the technician dialled in.

Everything about this nut is about resisting creep rather than carrying load. The adjuster is a threaded mechanism sitting in continuous vibration from the brush deck and the castor, and without a positive lock, the setting walks. The nylon insert holds the nut against that vibration so the blade angle found on a test lane is the same blade angle three weeks later.

This also makes it one of the few lock nuts on the machine that gets deliberately cycled. Every time the squeegee angle is reset, this nut comes off and goes back on, so its insert wears out faster than those on fixed pivots. That is worth knowing, because the symptom of a tired adjuster lock nut is not a loose nut — it is a squeegee that quietly drifts out of adjustment and gets blamed on the blades.

Inspect it at every adjustment. If the nut runs down the threaded bar under finger pressure alone, the insert is gone and it must be replaced. Also replace it if the insert is crumbling, melted or missing, if the hex corners are rounded, or if the bearing face is corroded. If the nut and the bar have galled, replace the nut and inspect the bar carefully before fitting the new one, since a damaged bar will destroy a fresh nut.

This is the genuine Tornado part in the correct size and pattern, so the adjuster locks positively and the blade angle stays where it was set.

Compatible Models

  • Tornado BD14/4 Disc Brush Autoscrubber — 99414
  • Tornado 20″ BD 20/11 — 99680
  • Tornado 18″ BR 18/11 — 99685
  • Tornado BD 22/14 — 99690
  • Tornado TS350-W20-U — 99694
  • Tornado BR 22/14 — 99695
  • Tornado BD 26/14 — 99720
  • Tornado BD 26/26 — 99726
  • Tornado BD 32/26 — 99732
  • Tornado BD 26/30 — 99760
  • Tornado BR 28/30 — 99765
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795
  • Tornado Formerly 99680L — TS120-S45-U
  • Tornado 99680blt — TS120-S53-U
  • Tornado 99694 — TS350-W20-U

This part is shared across 22 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the lock nut (part# 60221002) do on a Tornado floor scrubber?

It locks the squeegee tilt adjuster. Running on the threaded bar with its washer, it holds the blade-angle setting against the continuous vibration coming off the brush deck and the castor.

How do I know if the lock nut (part# 60221002) needs replacing?

If it runs down the threaded bar under finger pressure alone, the nylon insert is gone. Also replace it if the insert is crumbling, melted or missing, the hex corners are rounded, or the bearing face is corroded.

Why does this lock nut wear out faster than the others?

Because it is deliberately cycled. Every time the squeegee angle is reset, this nut comes off and goes back on, so its insert wears far quicker than those on fixed pivots. The symptom is not a loose nut but a squeegee that slowly drifts out of adjustment.

How do I order the Lock Nut (part# 60221002) or get help?

You can add the Lock Nut (part# 60221002) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the lock nut (part# 60221002) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Lock Nut 60221002”

Your email address will not be published. Required fields are marked *