Nut INOX 60210606

$1.99

Genuine OEM M6 stainless hex nut (part# 60210606), to UNI 5587, for Tornado floor scrubbers. On the squeegee control assembly it secures the break-away spring anchor, where the spring load is reacted into the linkage arm.

Genuine OEM M6 stainless (INOX) hex nut (part# 60210606), made to UNI 5587, used across a wide range of Tornado floor scrubbers — the full machine list is below. On the squeegee control assembly it is the nut at the spring anchor, sitting next to the break-away spring and the bushing that carries that pivot.

UNI 5587 specifies the tall pattern of hex nut rather than the ordinary one, which matters at this location. A taller nut engages more threads, so the clamp load is spread over more of the bolt and the joint is far less likely to strip or pull when the spring snatches at it. A standard-height nut substituted here is a joint waiting to fail under the one load case it exists to survive — the squeegee hitting something solid at speed.

The stainless specification is equally deliberate. The spring anchor is low down at the back of the machine, in the wettest place on it, permanently splashed with recovery water. A plated nut in that position rusts into the thread and the next person to service the squeegee will round it off or shear the stud getting it free. Stainless keeps the joint serviceable.

Replace this nut rather than reusing it whenever the spring is removed. A nut that has had spring load cycling through it for years has work-hardened threads and has usually lost the clean flank contact it started with. Signs it is past it: rounded corners on the hex, thread galling visible in the bore, a nut that runs on freely then binds, or any discolouration from heat or corrosion. Always check the mating stud and the bushing at the same pivot while the spring is off.

This is the genuine Tornado part in the correct size, pattern and material, so the clamp load at the spring anchor is what the design assumes rather than an approximation.

Compatible Models

  • Tornado 20″ BD 20/11 — 99680
  • Tornado 18″ BR 18/11 — 99685
  • Tornado TS350-W20-U — 99694
  • Tornado BR 22/14 — 99695
  • Tornado BD 26/14 — 99720
  • Tornado BD 26/26 — 99726
  • Tornado BD 28/20 — 99728
  • Tornado TS550-W28-U — 99729
  • Tornado BR 28/30 — 99765
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795
  • Tornado Formerly 99680L — TS120-S45-U
  • Tornado 99680blt — TS120-S53-U
  • Tornado 99694 — TS350-W20-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U
  • Tornado 99729 — TS550-W28-U

This part is shared across 23 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the nut (part# 60210606) do on a Tornado floor scrubber?

It secures the break-away spring anchor on the squeegee control assembly, holding the point where the spring load is reacted into the linkage arm.

What size and specification is it?

It is an M6 hex nut in stainless (INOX) to UNI 5587 — the tall pattern rather than the ordinary height, so it engages more threads and spreads the clamp load further along the bolt.

Can I use a standard-height M6 nut instead?

Not here. The tall UNI 5587 pattern is specified because this joint takes a snatch load every time the squeegee breaks away from an obstacle. A shorter nut engages fewer threads and is far more likely to strip under exactly the load case this fastener exists to survive.

How do I order the Nut INOX (part# 60210606) or get help?

You can add the Nut INOX (part# 60210606) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the nut inox (part# 60210606) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Nut INOX 60210606”

Your email address will not be published. Required fields are marked *