Nut INOX 60211002

$1.99

Genuine OEM stainless hex nut (part# 60211002) for Tornado floor scrubbers. On the squeegee control assembly it works in the tilt adjuster stack, locking against the threaded bar to hold the squeegee blade angle.

Genuine OEM stainless (INOX) hex nut (part# 60211002), used on a range of Tornado floor scrubbers — the full machine list is below. On the squeegee control assembly it belongs to the tilt adjuster group, running on the threaded bar alongside the lock nut and washers that fix the squeegee blade angle.

In an adjuster, a plain nut has a specific role: it is the one that sets the position, and a second fastener locks against it. That means this nut is turned deliberately and repeatedly over the life of the machine, every time a technician dials the squeegee angle in. It therefore sees far more thread cycles than a fastener that is tightened once and forgotten, and it wears accordingly.

Symptoms of a worn adjuster nut are subtle and usually blamed on something else. The adjustment feels vague, with no clear point at which the nut comes up against its seat. The setting creeps between services even though the lock nut was tightened. The nut runs freely over part of the bar and tightens unexpectedly elsewhere, which usually means the thread has picked up material from a damaged section of the bar. Grit in the thread produces the same symptom and is worth ruling out with a clean and a wire brush before condemning either part.

Stainless is specified because the adjuster sits in the splash zone and is handled with bare hands. A corroded adjuster nut is both harder to turn and more likely to gall on the bar, and galling is what destroys the threaded bar — a far costlier part. If this nut has seized before, replace the nut and inspect the bar closely before fitting the new one.

This is the genuine Tornado part in the correct size and material, so the adjuster keeps its full range of travel and its original feel.

Compatible Models

  • Tornado TS350-W20-U — 99694
  • Tornado BR 22/14 — 99695
  • Tornado BD 26/14 — 99720
  • Tornado BD 26/26 — 99726
  • Tornado BD 28/20 — 99728
  • Tornado TS550-W28-U — 99729
  • Tornado BD 32/26 — 99732
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BD 40/66 — 99790
  • Tornado BR 40/66 — 99795
  • Tornado 99694 — TS350-W20-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U
  • Tornado 99729 — TS550-W28-U

This part is shared across 19 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the nut (part# 60211002) do on a Tornado floor scrubber?

It runs on the threaded bar in the squeegee tilt adjuster. It is the nut that sets the position, with a second fastener locking against it to hold the squeegee blade angle in place.

How do I know if the nut (part# 60211002) needs replacing?

Signs are a vague adjustment with no clear seating point, a setting that creeps between services despite the lock nut being tight, or a nut that runs freely over part of the bar and binds elsewhere. Clean the thread and rule out grit before condemning it.

Why does it matter if this nut galls on the threaded bar?

Because the bar is much more expensive than the nut. A corroded or galled nut picks up material from the bar and damages the thread along its length. If this nut has seized before, replace it and inspect the bar carefully before fitting the new one.

How do I order the Nut INOX (part# 60211002) or get help?

You can add the Nut INOX (part# 60211002) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the nut inox (part# 60211002) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Nut INOX 60211002”

Your email address will not be published. Required fields are marked *