Nylon Lock Nut M3 60210304
$1.99
Genuine OEM M3 nylon lock nut (part# 60210304) for Tornado floor scrubbers. It secures small fastenings against vibration on control assemblies.
Genuine OEM M3 nylon lock nut (part# 60210304) for Tornado floor scrubbers — the machines it fits are listed below. In the drive wheel control assembly it secures a small fastening behind a board or bracket.
The nylon insert is what makes it a lock nut. As the nut runs up the thread, the insert deforms around the threads and grips them, providing friction that resists the rotation vibration would otherwise cause. On a machine that vibrates continuously, that friction is the difference between a component that stays where it was put and one that drifts.
At M3 the consequence of drift is particular. These nuts hold position-critical, low-load items — boards, small brackets, switch mountings. A nut backed off one turn does not drop anything; it lets the part move a millimetre, which is enough to change where a switch operates or to put strain on a connector, and the resulting fault is intermittent and hard to reproduce.
The locking feature is consumable. Each removal and refit deforms the insert further, and after two or three cycles the nut runs down with almost no resistance — at which point it is a plain nut that looks like a lock nut. Fit a new one whenever the joint is opened.
Nylon has a temperature limit, so do not reuse one that has been near a heat source and gone hard or glazed. Replace rather than reuse a nut that threads on easily by hand all the way, whose insert is missing, chewed or glazed, or whose hex is rounded — at M3 a rounded hex is very hard to grip.
Compatible Models
- Tornado BD14/4 Disc Brush Autoscrubber — 99414
- Tornado 17″ BD 17/6 Automatic Scrubber — 99617
- Tornado 20″ BD 20/11 — 99680
- Tornado 18″ BR 18/11 — 99685
- Tornado BD 22/14 — 99690
- Tornado TS350-W20-U — 99694
- Tornado BR 22/14 — 99695
- Tornado BD 26/14 — 99720
- Tornado BD 26/26 — 99726
- Tornado BD 28/20 — 99728
- Tornado TS550-W28-U — 99729
- Tornado BD 32/26 — 99732
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BD 40/66 — 99790
- Tornado BR 40/66 — 99795
- Tornado 99680blt — TS120-S53-U
- Tornado BDSO 20/21 — TS120-S59-U
- Tornado 99694 — TS350-W20-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
- Tornado 99729 — TS550-W28-U
This part is shared across 26 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the drive wheel control drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What does the M3 nylon lock nut (part# 60210304) do?
Its nylon insert deforms around the thread and grips it, providing friction that resists the rotation machine vibration would otherwise cause — so the small fastenings on control assemblies stay where they were put.
Why does one loose M3 nut matter?
Because these hold position-critical items like boards, brackets and switch mountings. A nut backed off a turn does not drop anything; it lets the part move a millimetre, which can change where a switch operates or strain a connector — an intermittent fault that is hard to reproduce.
Can I reuse it?
No. Each removal and refit deforms the insert further, and after two or three cycles it runs down with almost no resistance. Also discard any that has been near heat and gone hard or glazed — nylon has a temperature limit.
How do I order the Nylon Lock Nut M3 (part# 60210304) or get help?
You can add the Nylon Lock Nut M3 (part# 60210304) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the nylon lock nut m3 (part# 60210304) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet