Power Cord 25 ft. 18/3 SJT 19498

Genuine OEM power cord, 25 ft. 18/3 SJT (part# 19498), for commercial carpet spotters — a shared part fitted across Tornado and Powr-Flite machines as well as the PS Series spotter (see the list below). The dealer catalog lists it as “Power Cord 25′ 18/3 SJT”: 25 feet of three-conductor 18-gauge cable in an SJT jacket.

Compatible Models for the 25 ft. Power Cord

• Tornado PS Spotter 98220 — PS Series professional spotter, 115V
• Tornado PS8221 Spotter 98221 — the 230-volt build of the same spotter

The factory cross-reference returns six machines for this cord in total, across Tornado and Powr-Flite equipment. We publish only the models we can confirm against the manufacturers’ current catalogs — call us at 763-535-0770 with your model and serial number if yours is not listed and we will confirm it before you order.

What the specification means

Every part of “25 ft. 18/3 SJT” matters if you are tempted to substitute a generic cord.

18/3 is three conductors of 18 AWG — line, neutral and, critically, ground. A spotter is a wet machine with a mains motor and pump inside it; the ground conductor is what makes the chassis safe if a live connection ever reaches it. A two-conductor cord is not a substitute at any price.

SJT is the jacket rating: a junior service-grade thermoplastic jacket, rated for 300 volts and for hard service in the sense that matters here — it stays flexible, resists the moisture and detergent it will be dragged through, and takes being coiled and uncoiled several times a day without the jacket cracking. A cheap PVC extension-lead jacket goes stiff and splits.

25 feet is the factory length, which sets the machine’s working radius from one outlet. Fitting a shorter cord costs the operator reach; a much longer one adds voltage drop and extra cable to manage around furniture.

When to replace the power cord

A power cord is a wear part on a portable machine, and it is the one part where “run it a bit longer” is the wrong call. Replace it for any cut, split or abrasion through the outer jacket, any point where a conductor is visible, any exposed or bent pin on the plug, a plug body that is cracked or that has discoloured or melted around the pins, or a cord that has gone stiff or crazed with age.

Replace it too if the machine cuts out or flickers when the cord is flexed near either end, which indicates broken strands inside the jacket, and if the strain relief at the machine end has failed so the cord can be pulled against the internal connections. A cord that has been repaired with tape should be replaced, not re-taped.

Fitting notes

Isolate the machine before starting. Note the conductor terminations before disconnecting the old cord — photograph them — and make sure the ground conductor goes back to the same chassis point, properly tightened. Fit the cord through its strain relief and check that the relief grips the jacket, not the conductors, so any pull on the cord is taken by the jacket. Renew the strain relief if it is cracked or no longer clamps. Check that no conductor is pinched as the housing closes, and verify the ground connection before the machine goes back into service.

Twin City Vacuum has been selling and servicing commercial floor-care equipment since 1956.

You can browse every assembly for this machine on our Tornado PS Spotter 98220 parts page, and the manufacturer’s specifications are published at tornadovac.com.

Frequently Asked Questions

What size is the 25 ft. Power Cord 19498?

25 feet of three-conductor 18 AWG cable (18/3) in an SJT jacket, rated 300 volts. The third conductor is the ground, and 25 feet is the factory length for this machine.

Can I fit a generic extension cord instead?

No. A spotter is a wet machine with mains components inside, so the ground conductor is a safety requirement and a two-conductor cord is never a substitute. The SJT jacket also has to stay flexible and resist detergent and moisture through daily coiling — an ordinary PVC lead goes stiff and splits.

How do I know if the power cord needs replacing?

Replace it for any cut or abrasion through the jacket, any visible conductor, a cracked or heat-discoloured plug, bent or exposed pins, a jacket that has gone stiff or crazed, or a machine that flickers or cuts out when the cord is flexed near either end. A taped repair means replace, not re-tape.

How do I order the 25 ft. Power Cord (part# 19498) or get help?

You can add the 25 ft. Power Cord (part# 19498) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing commercial floor-care equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.