Tornado Screw 5/16-18 x 1 in. 03361
$1.99
Genuine OEM 5/16-18 x 1 in. machine screw (part# 03361) for commercial high-speed burnishers — shown on the Tornado Brute Force 1600 (98458B) and on the Brute Force 2000 (98482B) drawing.
The 03361 is a 5/16-18 coarse-thread screw, 1 inch long, used in the chassis hardware of the Brute Force burnishers. It appears on the Brute Force 1600 (98458B) main assembly drawing and on the Brute Force 2000 (98482B) main assembly drawing. Note that this screw does not appear on either of the Brute Force 2000 Dust Control (98486) drawings — that machine uses different hardware at the equivalent locations, which is a good example of why the part number matters more than the machine family. It is a shared part used across Tornado machines — see the full list of models below.
A 1 inch long 5/16-18 screw is a structural fastener on a machine this size, not trim hardware. If one is missing, loose, or has stripped threads, the joint it holds is carrying load it was not meant to carry, and on a burnisher that normally shows up as new vibration or a part that has started to shift. Replace rather than re-use a screw whose threads are galled or whose head is chewed up from a slipping tool — a damaged head is the reason a fastener gets rounded off and becomes a drill-out job later.
Fit the 03361 with the lock washer the drawing specifies for that callout and tighten to a firm, even torque. Over-torquing a 5/16-18 screw into a thinner bracket will pull the threads out of the bracket rather than the screw, which turns a one-dollar repair into a replacement panel. If you are reassembling after a motor or pulley job, check that the screw you removed matches this length — the drawings use several 5/16-18 screws in different lengths and they are easy to mix up on the bench.
This is shared hardware rather than a model-specific part, so it carries no model name. If you are not sure whether your machine takes the 03361 or one of the other 5/16-18 screws on the drawing, call us at 763-535-0770 with your model and serial number and we will check the callout with you.
Compatible Models
- Tornado models:
- 17″ 1.5 HP DS Series w/ Steel Base – Series B — 97580
- 17″ 1.5 HP DS Series w/ Steel Base – Series A — 97580C
- 20″ 1.5 HP DS Series w/ Steel Base – Series B — 97585
- 20″ 1.5 HP DS Series w/ Steel Base – Series A — 97585C
- Marathon Carpet Rinser/Dryer (10 Gallon) — 98172
- Marathon Carpet Rinser/Dryer (13 Gallon) — 98175
- 20″ High Speed Glazer (700/1500 RPM) w/ DC-PM Motor – Series U — 98440
- 20″ High Speed Glazer (1500 RPM) w/ AC Motor – Series F — 98445
- 20″ High Speed Glazer (1500 RPM) w/ DC-PM Motor – Series K — 98457
- Brute Force 1600 — 98458B
- 20″ High Speed Glazer (1500 RPM) w/ DC-PM Motor – Series K — 98464
- 17″ Bi-Speed Scrub/Buff w/ Quick-Grip Pad Holder – Series K — 98473
- 17″ Bi-Speed Scrub/Buff w/ Quick-Grip Pad Holder – Series A — 98473C
- 20″ Bi-Speed Scrub/Buff w/ Quick-Grip Pad Holder – Series K — 98480
- 20″ Bi-Speed Scrub/Buff w/ Quick-Grip Pad Holder – Series A — 98480C
- Brute Force 2000 High-Speed Glazer — 98482B
- P Series 2000 Glazer (230V) — 98487
- 20″ Clean-Air Glazer 2000 – Series J — 98492
- 17″ ES Series 8672 – 1.5 HP 115v – Series E — 98672
This part is used on many more Tornado and Powr-Flite machines than we can list here — call 763-535-0770 if yours is not shown and we will confirm it for you.
Frequently asked questions
Where is the 5/16-18 x 1 in. screw (part# 03361) used on a Brute Force burnisher?
It appears on the Brute Force 1600 (98458B) main assembly drawing and on the Brute Force 2000 (98482B) drawing. It is not used on the 98486 dust-control glazer.
How do I know if my 03361 screw needs replacing?
Replace it if the threads are galled or stripped, if the head is rounded from a slipping tool, or if it will not hold torque. A fastener that keeps loosening has usually damaged its own threads or the threads it goes into.
Does the 03361 screw fit the 98486 dust-control glazer?
No. The 03361 appears only on the 98458B and 98482B drawings. The 98486 uses different hardware at the equivalent locations — work from the 98486 drawing instead.
What models is the 5/16-18 x 1 in. screw (part# 03361) compatible with?
The Tornado Brute Force 1600 (98458B) and the Brute Force 2000 High-Speed Glazer (98482B). It is common hardware and is also used on other commercial floor machines.
How do I order the 5/16-18 x 1 in. screw (part# 03361) or get help?
You can add the 5/16-18 x 1 in. screw (part# 03361) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.






Reviews
There are no reviews yet