Screw M6 x 50 60130615
$1.99
Genuine OEM M6 x 50 mm screw (part# 60130615) for Tornado floor scrubbers. On the squeegee control assembly it secures the arm and pin group — the same length as the stainless screw used elsewhere in the linkage, but a different part with a different specification.
Genuine OEM M6 x 50 mm screw (part# 60130615) for Tornado floor scrubbers — the machine list is below. On the squeegee control assembly it is used in the arm and pin group, where the linkage arm is secured and located.
This screw is worth a word of warning, because the same assembly also uses a 50 mm M6 screw in stainless under a different part number. The two are the same nominal size and will both thread into either hole, so they get swapped by mistake during a rushed rebuild. They are not interchangeable in service: the stainless screw is specified for the wet, splash-exposed pivot, and this one for its own position. Fitting the wrong one at the wet pivot gives a screw that corrodes into its bushing, and fitting them the other way round wastes a more expensive fastener where it was not needed. Keep them separated on the bench and check the number before assembly.
In its own location the screw is a locating and clamping fastener rather than a bearing surface, so what you are checking for is different. Look at the thread first, along its whole length, because this is a fastener that may be removed and refitted several times over a machine life and the thread picks up damage from cross-starting. Then the head: a rounded socket or slot is a replace, since the next person will not be able to get it out at all. Finally check straightness by rolling it.
A practical tip: this group also contains a pin and a retaining clip. If the screw has been loose, the pin will have been moving too, so check the pin and fit a fresh clip while you are in there rather than reassembling with parts that have been working against each other.
This is the genuine Tornado part in the correct size and specification, so the joint clamps as designed and the linkage keeps its intended geometry.
Compatible Models
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BDSO 20/21 — TS120-S59-U
This part is shared across 5 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
Where is the screw (part# 60130615) used on a Tornado floor scrubber?
On the squeegee control assembly it is used in the arm and pin group, securing and locating the linkage arm.
Is this the same as the stainless M6 x 50 screw in the same assembly?
No, and this is a common mix-up. Both are 50 mm M6 and will thread into either hole, but they are different parts with different specifications. The stainless screw belongs at the wet, splash-exposed pivot; this one belongs in its own position. Check the part number before assembly.
How do I know if the screw (part# 60130615) needs replacing?
Check the thread along its whole length for damage from cross-starting, the head for a rounded socket or slot, and the shank for straightness by rolling it on a flat surface. Any of those means fit a new one.
How do I order the Screw M6 x 50 (part# 60130615) or get help?
You can add the Screw M6 x 50 (part# 60130615) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the screw m6 x 50 (part# 60130615) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet