Screw M8 x 16 INOX 60110804

$2.99

Genuine OEM M8 x 16 mm stainless screw (part# 60110804) for Tornado floor scrubbers. It is the short M8 fastener used in the steering group where the joint sits in the splash zone and must come apart again.

Genuine OEM M8 x 16 mm stainless (INOX) screw (part# 60110804), fitted to a range of Tornado floor scrubbers — the full machine list is below. On the steering wheel assembly it is the short M8 fastener specified for an exposed joint, where water running off the machine reaches the fastener head.

The stainless specification is the whole reason this is a separate part number from the plain M8 x 16 used elsewhere in the same assembly. They are the same nominal size, so they get confused on the bench, but they are not substitutes. In the wet position a plated screw corrodes into its thread; when somebody later needs that joint apart, the screw rounds off or shears and the repair becomes a drilling job in a bracket that was never meant to be disturbed.

The 16 mm length is equally specific. The steering group uses M8 screws at several lengths, and a longer one in a shallow boss bottoms out and gives a joint that feels tight while the parts are still loose.

Inspect at service. Replace it if the hex is rounded, if the thread is galled — stainless against stainless will gall if it is run in dry and fast — or if the shank shows stretch. Fit it steadily rather than with an impact driver, and renew the lock washer with it; a short fastener in an exposed joint depends on that washer to stay put.

This is the genuine Tornado part in the correct length, diameter and material, so the joint holds and still comes apart cleanly years later.

Compatible Models

This part is shared across 8 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the steering wheel drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

Why is this screw stainless when another M8 x 16 on the same assembly is not?

Because this one sits in the splash zone where water running off the machine reaches the fastener head. A plated screw there corrodes into its thread and rounds off or shears when the joint next needs to come apart.

Can I use the plain M8 x 16 instead?

No. They are the same nominal size and will thread into either hole, which is exactly why they get mixed up, but the plain screw in this wet position turns a future service into a drilling job.

How do I know if the screw (part# 60110804) needs replacing?

Replace it if the hex is rounded, if the thread has galled — stainless galls if run in dry and fast — or if the shank shows stretch. Fit the new one steadily rather than with an impact driver, and renew the lock washer with it.

How do I order the Screw M8 x 16 INOX (part# 60110804) or get help?

You can add the Screw M8 x 16 INOX (part# 60110804) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the screw m8 x 16 inox (part# 60110804) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Screw M8 x 16 INOX 60110804”

Your email address will not be published. Required fields are marked *