Small Metal Strain Relief SR37
$24.99
Genuine OEM small metal strain relief (part# SR37) for Tornado and Powr-Flite commercial high-speed burnishers — the two-piece cord clamp that anchors the power cord where it enters the machine. Fits all Tornado Brute Force burnishers (see full list below).
The SR37 is the small metal strain relief used at the cord entry on the Brute Force burnishers. It appears on every drawing in the book, on the Brute Force 1600 (98458B), on the Brute Force 2000 (98482B), and on the current and earlier Brute Force 2000 Dust Control (98486) drawings, listed alongside the SR36 washer and the M1407G power cord.
A metal strain relief grips the cord jacket between two clamping faces drawn together by a screw, so that any pull on the cord is taken by the chassis rather than by the conductors and their terminals. On a burnisher this part earns its keep daily. The cord is dragged across floors, pulled around door frames and occasionally yanked hard when it catches on a fixture, and each of those events is a direct tug on the wiring inside the machine.
Replace the SR37 if the clamp is cracked, if the screw boss is stripped so it can no longer be tightened, if the body is corroded, or if the clamping faces have cut into the cord jacket. The test is simple: with the machine unplugged, try to move the cord where it enters the machine. If the jacket slides, rotates or can be pushed in, the strain relief has stopped doing its job and the cord is being held by its own conductors. Fit a new one before the machine goes back into service — a broken ground conductor inside the handle gives no warning before it matters.
Replace it as a set with the SR36 washer and a new M1407G cord on any cord job, and make sure the clamp grips the jacket rather than crushing it: a strain relief tightened until it bites through the outer jacket damages the insulation it is meant to protect. The same strain relief is used across the Brute Force line, so this part carries no model name. Call 763-535-0770 if you want the full cord set listed for your machine. It is a shared part used across Tornado and Powr-Flite machines — see the full list of models below.
Compatible Models
- Tornado models:
- 17″ — 97590
- 20″ 1.5 HP M Series — 97595
- Brute Force 1600 — 98458B
- P Series 2000 Glazer (115V) — 98482
- Brute Force 2000 High-Speed Glazer — 98482B
- 20″ 1.5 HP — 98484
- Brute Force 2000 High-Speed Glazer with Dust Control — 98486
- Powr-Flite models:
- B171
- B172
- B201
- B202
- C131
- C171HD
- C201HD
- C202
- NM1600
- NM2000
- NM2000DC
Frequently asked questions
What does the small metal strain relief (part# SR37) do on a burnisher?
It clamps the power cord where it enters the machine so that pulling or dragging the cord loads the chassis rather than the electrical terminals and conductors inside.
How do I know if my SR37 strain relief needs replacing?
With the machine unplugged, try to move the cord at the entry point. If the jacket slides, turns or pushes in, the clamp has failed. Also replace it if the body is cracked or corroded or the screw boss is stripped.
Should I replace the cord and washer at the same time?
On a cord job, yes — the SR37 strain relief, the SR36 washer and the M1407G cord work as a set, and fitting a new cord into a worn clamp wastes the new cord.
What models is the small metal strain relief (part# SR37) compatible with?
All three Tornado Brute Force burnishers: the 1600 (98458B), the 2000 High-Speed Glazer (98482B) and the 2000 Dust Control (98486).
How do I order the small metal strain relief (part# SR37) or get help?
You can add the small metal strain relief (part# SR37) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.






Reviews
There are no reviews yet