Solution Pump without Mounts or Fittings FJ5082

Genuine OEM solution pump without mounts or fittings (part# FJ5082) for commercial carpet spotters and misters — a shared part fitted across Tornado and Powr-Flite machines as well as the PS Series spotter (see the full list below). The dealer catalog lists it as “Pump w/o Mounts No Fititings”, which is the supply spec rather than a description: the pump arrives as the bare unit, so the mounting hardware and fittings transfer from the pump you are replacing.

Compatible Models for the Solution Pump

• Tornado PS Spotter 98220 — PS Series professional spotter, 115V
• Tornado PS8221 Spotter 98221 — the 230-volt build of the same spotter

The factory cross-reference returns seventeen machines for this pump in total, spanning Tornado spotters and vapor misters and Powr-Flite equipment. We publish only the models we can confirm against the manufacturers’ current catalogs, so if yours is not listed, call us at 763-535-0770 with the model and serial number and we will confirm it before you order.

What the pump does and what “no mounts, no fittings” means

The pump is the heart of the spray side. It draws solution from the tank and delivers it to the tool at working pressure — on this class of machine around 55 PSI — so the operator can lay solution into a spot and then recover it. Everything downstream of the pump is plumbing; everything upstream is a reservoir. If the pump is not delivering, the machine is a vacuum cleaner.

“Without mounts” means the rubber isolating mounts that carry the pump on its plate are not supplied with it, and “no fittings” means the inlet and outlet fittings are not either. That is deliberate: the same pump is used across machines that mount it differently and plumb it differently, so the manufacturer supplies the common part and lets the machine-specific hardware come from the parts book. In practice it means you transfer the mounts and fittings from the old pump — and it is worth inspecting both while they are off, because a perished mount passes vibration straight into the plumbing and a fitting with a tired thread will weep on a new pump exactly as it did on the old one.

When to replace the pump

The clear cases are electrical or mechanical: a pump that does not run at all when the switch is set to spray, one that runs but produces no pressure, or one that has become noticeably noisier or is buzzing without pumping. A pump that cycles or pulses irregularly is often drawing air rather than failing, so check the inlet side first.

Before condemning a pump, rule out the cheaper causes, because they produce the same symptom of “no spray”. Check the solution filter screen for blockage, the inlet hose and its clamps for an air leak, the quick-disconnect coupler, the tool’s own jet for a blockage, and the switch and wiring. A blocked jet is by far the most common reason an operator believes the pump has died.

Fitting notes

Note the orientation and the inlet/outlet sides before removing the old pump — photographing the plumbing takes seconds and saves a rebuild. Transfer the mounts and fittings, renewing any that are perished or thread-damaged, and use fresh sealant or tape on tapered threads. Prime the system and check every joint under pressure before closing the machine up. Twin City Vacuum has been selling and servicing commercial floor-care equipment since 1956.

You can browse every assembly for this machine on our Tornado PS Spotter 98220 parts page, and the manufacturer’s specifications are published at tornadovac.com.

Frequently Asked Questions

What does the Solution Pump FJ5082 do?

It draws cleaning solution from the tank and delivers it to the tool under pressure, around 55 PSI on this class of machine. Without it the machine recovers water but cannot lay solution down.

What does “without mounts, no fittings” mean — what do I need to supply?

The pump arrives as the bare unit. The rubber isolating mounts and the inlet and outlet fittings are not included, because the same pump is mounted and plumbed differently across the machines that use it. You transfer them from the old pump — and it is worth replacing any mount that has perished or any fitting with a tired thread while they are off.

My spotter has stopped spraying — is it definitely the pump?

Not necessarily, and the cheaper causes are more common. Check the tool’s jet for a blockage first, then the solution filter screen, the inlet hose and clamps for an air leak, the quick-disconnect coupler, and the switch and wiring. Replace the pump when it will not run, runs without producing pressure, or buzzes without pumping.

How do I order the Solution Pump (part# FJ5082) or get help?

You can add the Solution Pump (part# FJ5082) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing commercial floor-care equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.