Spacer 47010010

$9.99

Genuine OEM spacer (part# 47010010) for Tornado floor scrubbers. It sets the stack height on the brush drive shaft so the hub and its bearing sit at the designed spacing.

Genuine OEM spacer (part# 47010010) for Tornado floor scrubbers — the machines it fits are listed below. On the brush base transmission it sits on the drive shaft as part of the stack that positions the brush hub and its support.

A spacer looks like the least interesting part in an assembly and is one of the easiest to get wrong. Its only job is to hold a precise distance, and everything stacked above and below it depends on that distance being right: bearing preload, how far the hub sits from its support, and whether the brush runs at the height the deck was designed around. Leave it out or substitute something close and the assembly goes together — it just runs loaded, or loose, in a way that is hard to diagnose later.

What goes wrong with the part itself is wear and deformation. If the components it separates have been running with play, the spacer takes a hammering and its faces go from flat to dished or stepped. Corrosion can pit the faces for the same reason the rest of this area suffers: it lives in solution spray and whatever the brushes throw. A spacer that is no longer flat and square no longer sets the distance it was made to set.

Inspect it whenever the hub is apart. Check both end faces for flatness and the bore for scoring, and measure its length against a new one if the assembly has been running noisy. Fit it with the rest of the stack in the order the parts came off; the sequence is part of the design, not a preference.

This is the genuine Tornado spacer at the correct length and bore.

Compatible Models

  • Tornado BD14/4 Disc Brush Autoscrubber — 99414
  • Tornado 17″ BD 17/6 Automatic Scrubber — 99617
  • Tornado BD 28/20 — 99728
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado Formerly 99680L — TS120-S45-U
  • Tornado 99680blt — TS120-S53-U
  • Tornado BDSO 20/21 — TS120-S59-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U

This part is shared across 9 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the brush base transmission drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

What does the spacer (part# 47010010) do?

It holds a precise distance in the brush drive shaft stack, which is what sets bearing preload, how far the hub sits from its support, and the height the brush runs at.

Can I leave the spacer out or substitute a similar one?

No. The assembly will still go together, which is the trap — it then runs either loaded or loose, and the resulting noise or wear is hard to trace back to a missing spacer later.

How do I tell if the spacer needs replacing?

Check both end faces for flatness and the bore for scoring with the hub apart, and measure its length against a new one if the assembly has been running noisy. A spacer that has been hammered by play runs dished or stepped and no longer sets the distance it was made to set.

How do I order the Spacer (part# 47010010) or get help?

You can add the Spacer (part# 47010010) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the spacer (part# 47010010) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

{“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does the spacer (part# 47010010) do?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It holds a precise distance in the brush drive shaft stack, which is what sets bearing preload, how far the hub sits from its support, and the height the brush runs at.”}},{“@type”:”Question”,”name”:”Can I leave the spacer out or substitute a similar one?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. The assembly will still go together, which is the trap — it then runs either loaded or loose, and the resulting noise or wear is hard to trace back to a missing spacer later.”}},{“@type”:”Question”,”name”:”How do I tell if the spacer needs replacing?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Check both end faces for flatness and the bore for scoring with the hub apart, and measure its length against a new one if the assembly has been running noisy. A spacer that has been hammered by play runs dished or stepped and no longer sets the distance it was made to set.”}},{“@type”:”Question”,”name”:”How do I order the Spacer (part# 47010010) or get help?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”You can add the Spacer (part# 47010010) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.”}}]}

Reviews

There are no reviews yet

Be the first to review “Spacer 47010010”

Your email address will not be published. Required fields are marked *