Spring 47210030
$3.99
Genuine OEM spring (part# 47210030) for Tornado stand-on and walk-behind floor scrubbers. It works with the squeegee tilt adjuster, keeping tension on the adjuster assembly so the blade angle the operator sets stays set.
Genuine OEM spring (part# 47210030), fitted to a wide range of Tornado stand-on and walk-behind floor scrubbers — the full machine list is below. On the squeegee control assembly it works alongside the tilt adjuster, the threaded bar and handwheel arrangement that sets how far the squeegee blade leans back against the floor.
Its job is to take up slack. The adjuster is a threaded mechanism with washers and a lock nut either side, and without a spring holding the stack in tension, vibration from the brush deck and the castor would let the setting creep. The spring keeps a constant load on the assembly so the blade angle the technician dialled in stays where it was put, run after run.
A tired or broken spring here does not stop the machine, which is exactly why it gets missed. What happens instead is that the squeegee needs adjusting more and more often: you set the angle, the machine dries the floor beautifully for a shift, and by the end of the week there is a film left behind again. Other signs are a rattle from the adjuster area, a handwheel that turns too easily, or visible gaps opening in the adjuster stack when the machine is at rest. If the spring is stretched so the coils no longer close up, it has lost its working load and will not come back.
Replacement is a short job and worth doing whenever the adjuster is apart for any other reason. Inspect the threaded bar for wear while you are in there, since a spring that has been weak for a while lets the adjuster rattle and that accelerates thread wear. Check the washers for cupping and renew the lock nut if the nylon insert has gone soft. Reset the blade angle afterwards and check the water line behind the machine on a test lane.
Because this is the genuine Tornado part, the rate and free length match the original, so the adjuster holds its setting with the same feel as it did new.
Compatible Models
- Tornado 20″ BD 20/11 — 99680
- Tornado 18″ BR 18/11 — 99685
- Tornado BD 22/14 — 99690
- Tornado TS350-W20-U — 99694
- Tornado BR 22/14 — 99695
- Tornado BD 26/14 — 99720
- Tornado BD 26/26 — 99726
- Tornado BD 32/26 — 99732
- Tornado BD 26/30 — 99760
- Tornado BR 28/30 — 99765
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BR 40/66 — 99795
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado 99694 — TS350-W20-U
This part is shared across 20 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What does the spring (part# 47210030) do on a Tornado floor scrubber?
It keeps tension on the squeegee tilt adjuster. The adjuster sets how far the blade leans back against the floor, and the spring stops vibration from working that setting loose between services.
How do I know if the spring (part# 47210030) needs replacing?
The tell-tale is a squeegee angle that will not stay set. If you adjust the blade, get a dry floor for a shift or two, and then the film comes back, suspect this spring. Look also for a rattle at the adjuster, a handwheel that spins too freely, or a spring whose coils no longer close up.
Is it worth replacing while the machine still works?
Yes, if the adjuster is already apart. It is an inexpensive part and a weak spring lets the adjuster rattle, which wears the threaded bar — a far more expensive thing to replace. Changing it during any adjuster service is cheap insurance.
How do I order the Spring (part# 47210030) or get help?
You can add the Spring (part# 47210030) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the spring (part# 47210030) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet