Spring Clip 62120604
$1.99
Genuine OEM spring clip (part# 62120604) for Tornado floor scrubbers. It is the sprung retainer that holds a shaft or pin in the squeegee control linkage, designed to be pulled off by hand for service and to snap back under its own tension.
Genuine OEM spring clip (part# 62120604), fitted to a range of Tornado floor scrubbers — see the machine list below. On the squeegee control assembly it retains a shaft in the linkage, holding it against the vibration of normal running while still coming off by hand when the squeegee needs servicing.
This is a different animal from a plain retaining clip. A spring clip is designed to be removed and refitted regularly as part of routine squeegee service, so it is made to flex further and return. That is also its weakness: every cycle works the spring steel a little, and a clip that has been pulled off at every blade change for two years will eventually stay open instead of snapping closed.
Signs it is done: the clip no longer springs back tight against the shaft, it sits proud or crooked rather than seating fully, you can lift it off with almost no force where it used to need a deliberate pull, or there is a visible crack or kink where it bends. Rust is the other killer — once corrosion reaches the sprung section, the clip loses its temper and will not hold reliably even if it looks intact.
Keep a spare on the shelf. This is a part that costs very little and is needed at the least convenient moment, usually with the machine half apart and a floor to finish. When fitting, make sure the clip seats fully into its groove and sits square; a clip that is only partly home will come off on the first hard knock.
This is the genuine Tornado part, so it matches the original shaft diameter and groove, and it has the spring temper the design relies on rather than the approximate fit of a generic substitute.
Compatible Models
- Tornado BD14/4 Disc Brush Autoscrubber — 99414
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BDSO 20/21 — TS120-S59-U
This part is shared across 6 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What does the spring clip (part# 62120604) do on a Tornado floor scrubber?
It is a sprung retainer holding a shaft in the squeegee control linkage. It keeps the shaft captive during normal running but is designed to come off by hand so the squeegee can be serviced without tools.
How do I know if the spring clip (part# 62120604) needs replacing?
If it no longer snaps back tight against the shaft, sits proud or crooked instead of seating fully, lifts off with almost no force, or shows a crack, a kink or rust in the sprung section, replace it. A clip that has lost its temper will not hold even though it looks fine.
How is this different from the plain retaining clip in the same assembly?
A spring clip is built to be removed and refitted regularly during routine squeegee service, so it flexes further and is meant to return. A plain retaining clip is fit-and-forget. That is also why a spring clip wears out with use and is worth keeping as a shelf spare.
How do I order the Spring Clip (part# 62120604) or get help?
You can add the Spring Clip (part# 62120604) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the spring clip (part# 62120604) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet