Strain Relief Washer SR36

$4.99

Genuine OEM strain relief washer (part# SR36) for Tornado and Powr-Flite commercial high-speed burnishers — the washer that works with the SR37 metal strain relief to clamp the power cord where it enters the machine. Fits all Tornado Brute Force burnishers (see full list below).

The SR36 strain relief washer is the companion piece to the SR37 small metal strain relief. Together they clamp the 12/3 power cord (M1407G) where it enters the machine. The washer appears on every Brute Force burnisher drawing — shown on the Brute Force 1600 (98458B), on the Brute Force 2000 (98482B), and on the current and earlier Brute Force 2000 Dust Control (98486) drawings — always listed next to the strain relief and the cord.

Strain relief is the single most important detail on a corded floor machine. The cord on a burnisher gets stepped on, dragged around corners, wound and unwound dozens of times a shift, and yanked when it snags. Every one of those loads wants to pull the cord out of the machine and put tension on the terminal screws inside. The washer and strain relief transfer that load into the chassis instead, so the conductors inside never see it.

Replace the SR36 if it is deformed, cracked, corroded or missing, and replace it as a matter of course whenever you fit a new power cord. The symptom that matters is a cord that can be moved or twisted where it enters the machine: if you can rotate or push the jacket in and out by hand, the clamp is no longer gripping and the cord is being held by its own conductors. That is how a hot joint, an intermittent fault, or a broken ground wire starts. Do not run a machine with the cord entry clamp missing.

The same washer is used across the Brute Force line, so it carries no model name. Order it together with the SR37 strain relief and a new cord if you are doing a full cord replacement — the three parts work as a set. Call 763-535-0770 if you want us to confirm the set for your machine from its model and serial number. It is a shared part used across Tornado and Powr-Flite machines — see the full list of models below.

Compatible Models

  • Tornado models:
  • Powr-Flite models:
    • B171
    • B172
    • B201
    • B202
    • C131
    • C171HD
    • C172
    • C201HD
    • C202
    • NM1600
    • NM171HD
    • NM171SD
    • NM2000
    • NM201HD
    • NM202

Frequently asked questions

What does the strain relief washer (part# SR36) do on a burnisher?

It works with the SR37 metal strain relief to clamp the power cord where it enters the machine, so pulling or dragging the cord loads the chassis instead of the electrical connections inside.

How do I know if my SR36 strain relief washer needs replacing?

If you can push, pull or twist the cord jacket by hand where it enters the machine, the clamp is no longer gripping. Replace the washer if it is deformed, cracked or corroded, and always fit a new one with a new cord.

Do I need the SR37 as well?

Usually yes — the SR36 washer and the SR37 metal strain relief are used together, and on a cord replacement it is worth fitting both along with the new M1407G cord.

What models is the strain relief washer (part# SR36) compatible with?

All three Tornado Brute Force burnishers: the 1600 (98458B), the 2000 High-Speed Glazer (98482B) and the 2000 Dust Control (98486).

How do I order the strain relief washer (part# SR36) or get help?

You can add the strain relief washer (part# SR36) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.

Reviews

There are no reviews yet

Be the first to review “Strain Relief Washer SR36”

Your email address will not be published. Required fields are marked *